Black Horce Model NC76510 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 21

background image

PIPER CUB - EP.

INSTRUCTION MANUAL

6

Attach the micro control connector to the
servo arms. Be sure to use the lock tie but it
could free rotation.

Micro control connector.

Repeat the procedure for the other
wing half.

JOINING THE WING HALVES.

1. Locate the aluminium wing dihedral

brace.

2. Test fit the dihedral brace into each

wing half. The brace should slide in easily.

C/A glue.

Cut

«
...
4
5
6
7
8
...
»

Содержание NC76510






















Отзывы:

Нет отзывов

Похожие инструкции для NC76510

Бренд: L. G. B. Страницы: 4

Бренд: Bachmann Страницы: 2

Бренд: Dancing Wings Hobby Страницы: 2

Бренд: T-Motor Страницы: 2

Бренд: H-KING Страницы: 15

Бренд: GRAUPNER Страницы: 21

Бренд: H-KING Страницы: 11

Бренд: E sky Страницы: 140

USRA 0-8-0 Steam Locomotive and Tender

Бренд: Lionel Страницы: 36

Peche aux Canards

Бренд: Lansay Страницы: 2

Бренд: Eduard Страницы: 4

Бренд: Trix Страницы: 20

Бренд: QABA Страницы: 4

Missions In Space 15118

Бренд: K'Nex Страницы: 35

Sector 3 Sphere Couplet

Бренд: Tabletop Scenics Страницы: 35

Panzer IV Ausf. H zimmerit

Бренд: Eduard Страницы: 4

Бренд: Phoenix Model Страницы: 17

Star Coaster Level 5

Бренд: InVento Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды