Black Box MT1000A-13 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 44

Black Box MT1000A-13 Скачать руководство пользователя страница 4

TRADEMARKS/WARNINGS

3

TRADEMARKS USED IN THIS MANUAL

ST is a registered trademark of AT&T.

Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.

WARNING

These products are equipped with a laser diode. Please observe the following
precautions:

• Before turning on the equipment, make sure that the fiber optic cable is intact and is

connected to the transmitter.

• Do not attempt to adjust the laser drive current.

• Do not use broken or unterminated fiber optic cables/connectors or look straight at

the laser beam.

• Using optical devices with this equipment will increase the risk of eye injury.

• Performing procedures other than those specified herein may result in hazardous

radiation exposure.

CAUTION: The laser beam may be invisible!

Always observe standard safety precautions during product installation, operation,
and maintenance. Only qualified and authorized service personnel should carry out
product adjustment, maintenance , or repairs. No installation, adjustment,
maintenance, or repairs should be performed by either the operator or the user.

«
...
2
3
4
5
6
...
»

Содержание MT1000A-13













































Отзывы:

Нет отзывов