Black Box ME260A страница 41 Скачать руководство пользователя

Страница: 41 / 50

MODULAR MODEM ELIMINATOR

5. Troubleshooting

5.1 Things To Try

In case a problem occurs, perform the following checks:

• Check that the PWR indicator lights. If not:

Check that both ends of the AC power cable are properly connected.

- Disconnect the AC cable from both ends and check the Modem Eliminator’s

fuse (located in the AC power connector). If the fuse is blown, replace it with
a fuse of proper rating.

- Replace the Modular Modem Eliminator.

• Check that the appropriate MODE indicator lights. If not, set the internal

MODE SELECT jumper to the correct position.

• Check that the internal jumpers and the interface module internal switches

are set to the correct positions. See

Sections 3.2.3

and

3.2.4

• Check that the cables between the Modular Modem Eliminator and the

attached equipment are properly connected.

5.2 Calling Black Box

If you determine that your Modular Modem Eliminator is malfunctioning,

do not

attempt to alter or repair the unit

. It contains no user-serviceable parts. Contact Black

Box Technical Support at 724-746-5500.

Before you do, make a record of the history of the problem. We will be able to

provide more efficient and accurate assistance if you have a complete description,
including:

• the nature and duration of the problem;

• when the problem occurs;

• the equipment involved in the problem;

• any particular application that, when used, appears to create the problem or

make it worse; and

• the results of any testing you’ve already done.

Содержание ME260A


















































Результаты поиска

Содержание ME260A

Отзывы:

Похожие инструкции для ME260A

Бренды по названию

Популярные бренды

Black Box ME260A, Руководство пользователя

Результаты поиска

Содержание ME260A

Отзывы:

Похожие инструкции для ME260A

Бренды по названию

Популярные бренды