Black Box ME260A Скачать руководство пользователя | Manualshive

Страница: 37 / 50

background image

36

MODULAR MODEM ELIMINATOR

3.5 Connecting the Cables

3.5.1 C

ONNECTOR

L

OCATION

Figure 3-6

identifies the connectors located on the rear panel of the Modular

Modem Eliminator. For information on connector wiring, refer to

Appendix A

.

Figure 3-6. Rear Panel.

3.5.2 D

ATA

C

ONNECTIONS

Refer to the installation plan and connect the data cables to the interface module
connectors J1 and J2.

3.5.3 P

OWER

C

ONNECTION

WARNING

When you plug in the Modem Eliminator, the protective earth terminals
of this instrument must be connected to the protective ground
conductor of the power cord. The plug must be inserted only in an outlet
provided with a protective earth (grounding) contact. The protective
action must not be negated by use of an extension cord without a
grounding conductor. Make sure that only fuses of the required rating,
as marked on the Modem Eliminator’s rear panel, are used for
replacement. Avoid using repaired fuses and short-circuiting fuse
holders. Whenever it is likely that the protection offered by fuses has
been impaired, the instrument must be made inoperative and be secured
against any unintended operation.

AC power should be supplied to the Modular Modem Eliminator through the
5-foot (1.5-m) standard power cable terminated by a standard 3-prong plug.
Connect the cable between the AC mains connector on the rear panel and
a standard grounded AC outlet.

AC Power

Connector

Connector J2

Connector J1

Fuse

Compartment

«
...
35
36
37
38
39
...
»

Содержание ME260A



















































Отзывы:

Нет отзывов

Похожие инструкции для ME260A

Бренд: Campbell Страницы: 3

Sierra Wireless AirLink RV50

Бренд: Campbell Страницы: 2

Бренд: PROLiNK Страницы: 10

Бренд: Bell Страницы: 47

Бренд: Paradyne Страницы: 2

Plus TV PVR-TV 305U

Бренд: KWorld Страницы: 9

AP Broadband modem

Бренд: IPWireless Страницы: 37

Бренд: Zoom Страницы: 2

Бренд: Zoom Страницы: 32

Бренд: Zoom Страницы: 33

Бренд: Spectrum Страницы: 8

Бренд: Cradlepoint Страницы: 104

Бренд: Telecom Страницы: 41

Cerberus P 6331-4A

Бренд: Pentagram Страницы: 62

Cerberus Wi-Fi Lite

Бренд: Pentagram Страницы: 64

Cerberus ADSL2+ Lite

Бренд: Pentagram Страницы: 75

Бренд: NETGEAR Страницы: 208

FASTRACK M13006B

Бренд: M2M Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды