Black Box ME260A страница 32 Скачать руководство пользователя | Manualshive

Страница: 32 / 50

background image

31

CHAPTER 3: Installation

NOTE

The functions of all the following jumpers are used only in the ME
(modem eliminator) mode.

CARRIER-2, JP5 (ME mode only)

• ON—The DCD line in connector J2 is continuously on.

• CTRL—The DCD line in connector J2 tracks the RTS line in connector J1.

The Modular Modem Eliminator is shipped with the jumper set at ON.

CARRIER-1, JP4 (ME mode only)

Same as JP5 for the DCD line in connector J1.

XMT TIMING, JP3 (ME mode only)

Selects the timing source in the ME mode:

• INT—Modular Modem Eliminator internal oscillator. The data rate

is determined by the RATE selector.

• EXT J1—The transmit clock applied to connector J1. The data rate

equals the clock rate.

The Modular Modem Eliminator is shipped with the jumper set at INT.

DELAY 1, JP2 (ME mode only)

Selects the delay between the activation of the RTS line in connector J1 and the
activation of the CTS line in the same connector. The available selections are 0, 6,
and 51 ms.

The Modular Modem Eliminator is shipped with the jumper set at 0 ms.

DELAY 2, JP1 (ME mode only)

Same as JP2 for connector J2.

«
...
30
31
32
33
34
...
»

Содержание ME260A



















































Отзывы:

Нет отзывов

Похожие инструкции для ME260A

Бренд: FALCOM Страницы: 22

Zlinx Xtreme IP67 ZXT9-RM

Бренд: B&B Electronics Страницы: 164

Бренд: NAL Страницы: 158

Бренд: Data-Linc Group Страницы: 15

Бренд: RCA Страницы: 21

Бренд: Myzone Страницы: 4

Бренд: Ebyte Страницы: 34

Бренд: Teltonica Страницы: 19

Бренд: CTC Union Страницы: 43

Бренд: Elastic Networks Страницы: 32

Бренд: RIM Страницы: 76

Бренд: ICT Страницы: 22

GTM-204M-4G Series

Бренд: ICP DAS USA Страницы: 41

Бренд: Paradyne Страницы: 280

Бренд: Wavecom Страницы: 96

EdgeAccess Universal Chassis System 2361 T1

Бренд: Canoga Perkins Страницы: 74

Бренд: Ebyte Страницы: 35

Бренд: CNI Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды