Black Box ME0006A-V35 Скачать руководство пользователя страница 7

Страница: 7 / 32

2-WIRE SHORT-RANGE DSL LINE DRIVER (HDSL WITH V.35 OR X.21)

1. Specifications

Clocking Modes:

Internal, external, or receive recovered

DTE Rate:

All 64-kbps increments from 64 to 1152 kbps

DTE Interface:

ME0006A-V.35: DCE orientation; ME0006A-X.21: DCE or DTE

DTE Connector:

ME0006A-V.35: M/34 female; ME0006A-X21: DB15 female

Diagnostics:

V.52-compliant (511/511E) pattern generator and detector with error

injection mode controlled by a front-panel switch; local and remote loopback
controlled by either a front-panel switch or from the DTE interface

Indicators:

LEDs: DSL Link (green active); TD (yellow/green) idle yellow; RD

(yellow/green) idle yellow; NS (red active); No signal DSL Link; ER (flashing red)
CRC error during normal operation, bit error during pattern-generation test; TM
(active yellow) Test Mode enabled

Configuration:

Externally accessible DIP switches or SNMP managed through

ME0003C

Transmission Line:

Single twisted pair

Line Coding:

2B1Q

Line Rates (DSL Line):

144, 272, 400, 528, 784, 1040, 1168 kbps

Line Interface:

Transformer coupled, 1500-VAC isolation

Connection:

RJ-45, 2-wire, polarity insensitive pins 4 and 5

Operating Temperature:

32 to 122°F

(

0 to 50°C)

Humidity:

5 to 95% noncondensing

Altitude:

Up to 15,000 ft. (4572 m)

Power:

External desktop transformer, 100 to 240 VAC, 50 to 60 Hz (universal

input), 10 W

Size:

1.6"H x 4.7"W x 6"D (4.1 x 11.9 x 15.2 cm)

Weight:

0.58 lb. (0.26 kg)

Содержание ME0006A-V35
































Результаты поиска

Содержание ME0006A-V35

Отзывы:

Похожие инструкции для ME0006A-V35

Бренды по названию

Популярные бренды

Black Box ME0006A-V35, Руководство пользователя

Результаты поиска

Содержание ME0006A-V35

Отзывы:

Похожие инструкции для ME0006A-V35

Бренды по названию

Популярные бренды