Black & Decker BCSS820, Инструкция по эксплуатации

Страница: 10 / 36

English
8
Installing and Removing the Battery Pack
(Fig. E)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
14 into the tool handle, align the
battery pack with the rails inside the tool’s handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
15 and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Fitting and Removing Blades (Fig. C, D)
The grass shear blade 5 has been designed for trimming
grass and weeds. The shrub trim blade 6 has been designed
for trimming hedges and shrubs.
• To fit the blade, remove the blade cover
8 by pushing
and holding the blade release button 9 in the direction
of the arrow (Fig. C)
• Remove the blade cover 8 (Fig. C).
• Align the positioning pin holes 10 on the blade with the
positioning pins 11 .
• Replace the blade cover 8 as shown in Fig. C.
• The blade release button snaps into closed position.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start‑up can cause injury.
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING:
Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
• The charger is designed to operate on standard
120V household electrical power. Do not attempt to
use it on any other voltage. This does not apply to the
vehicular charger.
• Foreign materials of a conductive nature, such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil or any buildup of metallic particles
should be kept away from the charger cavities.
•
Always unplug the charger from the power supply
when there is no battery pack in the cavity.
Charging a Battery (Fig. B)
1. Plug the charger into an appropriate outlet.
2. Insert and fully seat battery pack. Green charging light
will continuously blink while charging.
3. Charging is complete when the green light remains
continuously ON. Battery pack can be left in charger
or removed.
WARNING:
Only charge batteries in air temperature
over 40° F (4.5° C) and below 105° F (+40.5° C).
4. Charger will not charge a faulty battery pack, which may
be indicated by the light staying OFF or the red light
rapidly blinking. Take charger and battery pack to an
authorized service center if light stays OFF or red light
rapidly blinks.
nOTE: Refer to label near charging light on charger for
blink patterns.
hot/Cold Pack Delay
When the charger detects a battery pack that is too hot
or too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery pack life.
A cold battery pack may charge at a slower rate than a warm
battery pack.
The hot/cold pack delay will be indicated by the red light
continuously flashing a short ON followed by a longer ON
(see charger for blink pattern). Once the battery pack has
reached an appropriate temperature, the charger will resume
the charging procedure.
Electronic Protection System
Li-Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;