BK Precision 2522B Скачать руководство пользователя страница 8

Trigger Sensitivity:

AC:

1.0 div (internal)

0.5 Vp-p (external)

30 Hz – 30 MHz

TV-V:

1.0 div (internal)

0.5 Vp-p (external)

20 Hz – 30 kHz

TV-H:

1.0 div (internal)

0.5 Vp-p (external)

3 kHz – 100 kHz

Maximum External Trigger Voltage: 300 V (dc + ac

peak).

DIGITAL STORAGE FACILITIES

Storage Word Size:

2048

3

8 bits/channel (2 k/channel with direct sam-

pling, 1 k/channel with equivalent time sampling).

Vertical Resolution:

8 bit (1 in 256) approximately 25 steps/div.

Horizontal Resolution:

1 in 2048, approximately 200 samples/div.

Sampling Rate:

10 M samples/sec to 4 samples/sec, reduced in propor-
tion to time base. Direct sampling at time base settings
of 20

µ

s/div and slower, equivalent time sampling at

time base settings of 10

µ

s/div and faster.

Time Base Expander:

For storage of slow time events, time base steps
10 ms/div and slower have selectable 1/1 or 1/100 rate.
1/100 rate expands time base from 1 sec/div to 50
sec/div in 1-2-5 sequence.

Equivqlent Time Sampling Bandwidth:

20 MHz for repetitive waveforms.

Dot Joining:

Linear interpolation between samples.

Digital Display Modes:

Roll:

Stored data and display updated continually.

Refresh:

Stored data and display updated by triggered sweep.

Hold:

Freezes channel 1 and channel 2 data immediately.

Save CH 2:

Freezes channel 2 data immediately.

Pretrigger Storage:

Available in single sweep mode, switchable to 0%,
25%, 50%, or 75%.

PLOT OUTPUT

Analog output of the stored display.

CH 1 and CH 2 Outputs:

Selected by PLOT switch. Output via CH1 OUTPUT
and CH2 OUTPUT jacks on rear panel. Amplitude
0.2 V/div (2 V maximum).

Output Sweep Rate:

Output sweep rate is 1/10 of TIME/DIV setting (and
1/100 switch when applicable).

Pen Lift Output:

Available at PEN DOWN jack on rear panel, TTL high,
pen up. TTL low, pen down.

OTHER SPECIFICATIONS

Cal/Probe Compensation Voltage: 0.5 V p-p

±

3% square

wave, 1 kHz nominal.

CH 2 (Y) Output:

Output Voltage: 50 mV/div (nominal into 50 ohm

load).

Output Impedance: Approximately 50 ohms.

Frequency Response: 20 Hz to 20 MHz,

3 dB.

Power Requirements: 100–130 VAC or 200–260 VAC,

50/60 Hz, 55 watts.

Dimensions (H

3

W

3

D):

5.2

3

12.8

3

15.7

(132

3

324

3

398 mm).

Weight: 18.7 lbs (8.5 kg).

Environment:

Within Specified Accuracy: +10° to +35° C, 10–80%

relative humidity.

Full Operation: 0° to +50° C, 10–80% relative

humidity.

Storage:

30° to +70° C, 10–90% relative humidity.

ACCESSORIES SUPPLIED:

Two Switchable X1/X10 Probes.

Instruction Manual.
AC Line Cord.

SPECIFICATIONS

6

Содержание 2522B




























Отзывы: