Bistos BT-780 Скачать руководство пользователя страница 5

Страница: 5 / 51

BT-780 Operation manual

P/N : 780-ENG-OPM-EXP-R00

Bistos Co., Ltd.

2020.03

0 Safety information

Before using BT-780 Patient monitor, read this entire manual and be fully understood the following safety information to prevent

injury of patient and user.

Symbols Used

The following symbols identify all instructions that are important to safety. Failure to follow these instructions can lead to injury or

damage to the patient monitor. When used in conjunction with the following words, the symbols indicate:

WARNING

Can lead to serious injury or death.

CAUTION

Can lead to minor injury or product/property damage

The following symbols are placed on product, label, packaging and this manual in order to stand for the information about:

Used to identify safety information.

Be well-known this information thoroughly before using BT-780.

Used to identify safety information.

Be well-known this information thoroughly before using BT-780

IPX1

Indicates the protection level against the ingress of liquid.

IPX1 is protection against some water drops falling vertically.

It correspond the device, patient monitor and accessory, temperature sensor

IPX2

Indicates the protection level against the ingress of liquid.

IPX2 is protection from some water drops when the device is tilted up to and including 15°.

It correspond the accessories for SpO2 and ECG.

Refer to operation manual. Read manual before placing the device.

Indicates AC power supply

Indicates the device is in the battery operation mode.

Fuse

Equipotentiality

Indicates nurse call interface.

Indicates network interface.

Indicates USB interface.

Indicates the production date.

Indicates the manufacturer.

Indicates the serial number of the device.

Indicates the authorized representative in the European Community of manufacturer.

Indicates a defibrillation-proof type BF applied part.

Indicates a defibrillation-proof type CF applied part.

Indicates the date after which the medical device is not to be used.

Содержание BT-780




















































Результаты поиска

Содержание BT-780

Отзывы:

Похожие инструкции для BT-780

Бренды по названию

Популярные бренды

Bistos BT-780, Руководство по эксплуатации

Результаты поиска

Содержание BT-780

Отзывы:

Похожие инструкции для BT-780

Бренды по названию

Популярные бренды