background image

INSTALLATION, OPERATION AND MAINTENANCE MANUAL 

 

BiSolid Comfort                                                                                    OM-BSCV00/08/2012/EN 

29 

 

7. BOILER INSTALLATION INSTRUCTIONS 

 

7.1. BOILER INSTALLATION – OVERAL INFORMATION

 

 

The hot water boilers from series BiSolid Comfort 03/04/05 must be initianted into operation by 
authorized  servicing  technicians.  The  existing  network  of  authorized  servicing  organizations 
which  comply  with  this  condition  is  able  to  take  responsibility  for  all  boiler  installations,  their 
initialization in operation and warranty repairs.  
 
The boiler is designed to supply heating systems with pressure up to 400 kPa by using water, 
which  must  compy  to  the  standard  requirements  (under  no  circumstances  the  water  can  be 
acidic, i.e. it must have hydrogen exponent pH>7 and minimum carbon hardness). The heating 
system must be designed in such way that the hot water circulates at least through some of 
the radiators at all times.  
 
We do not recommend the usage of antifreeze liquids because of their unsuitable properties. 
Such  liquids  have  decreased  heat-exchanging  capabilities,  high  volume  expansion  and 
harmfull components.  
 
Before final installation, the distribution pipelines of the heating system must be rinsed several 
times with water under pressure. In old, already used systems, the rinsing has to be performed 
in opposite direction to the heated  water circulation. In new systems all radiators have to be 
cleaned from erosive materials and rinsed with warm water under pressure.  
 
We recommend installation of precipitant on the boiler entrance (i.e. on the boiler’s hot water 
return  pipeline).  The  precipitant  should  be  designed  with  availability  for  emptying  on  regular 
intervals, without necessity of draining too much hot water. The precipitant can be combined 
with filter, but the filter itself is not enough to secure adequate protection.  
 

 
Warning 
The  system  must  be  connected  to  open  type  expansion  tank,  for  safety 
reasons.  
Any  of  the  stopping  fittings  must  not  be  connected  to  the  inlet  or  the  safety 
outlet pipelines.   
For  increasing  the  system  safety  a  bypass  line  must  be  installed  on  the  inlet 
and outlet line of the circulations pump, as presented on the diagrams. 
The bypass line valve must be closed when the boiler operates normally.  
The  bypass  line  valve  can  be  used  when  there  are  problems  with  the  power 
supply  and  must  be  opened  if  there  is  any  risk  of  heating  system  water 
overheating, caused by power supply failure or another problem.  
The pipelines diameter installed in the bypass line must be at least equal of the 
water supply pipeline. 
UPS (uninterruptible power supply) can be used for prevention of power supply 
failures.  

 

Warning 
All problems (faults) with the boiler caused by clogging with dirt from the heating 
system or faults caused by clogging are not covered by the product warranty. 

 
 

Содержание Comfort 03









































Отзывы: