CONSUMER SAFETY INFORMATION
(For 120 NEMA 1-15P plugs only)
This appliance
has a polarized plug (one blade is wider than the
other). To reduce the risk of electric shock, this
plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified
electrician. DO NOT MODIFY THE PLUG IN
ANY WAY.
ASSEMBLY INSTRUCTIONS
NOTE:
A Phillips screwdriver is required for
assembly.
Unpack your heater from the box, being careful
to remove all parts from plastic bags and
remaining packaging. Please save the carton for
off-season storage.
This model is packed with separate base and
pedestal in the box. Carefully remove all parts
from plastic bags. To prevent scratches, place all
parts onto a cloth before assembly. Follow the
below instructions for Pedestal/Base assembly:
Pedestal Assembly
Step 1: Run the power cord through the center
of the assembled pedestal. Snap
pedestal into the bottom of the heater
housing. Refer to Figure 1, 2.
BASE ASSEMBLY
Step 1: Run the power cord through the center
of the base. To assemble the base to
the unit first make sure the side
marked “Rear” is facing the back of
the heater. Line up holes of the base
with holes on bottom of pedestal (or
heater housing if no pedestal is
included), and secure with 4 provided
screws. Refer to Figure 3.
Step 2: Lace the power cord through the cord
minders on the underside of the base.
Refer to Figure 4.
Step 3: Turn the heater right side up on a flat
level surface prior to beginning
operation.
OPERATING INSTRUCTIONS
1. Place heater on a firm, level surface.
2. Plug heater into a standard outlet. Once
plugged in, the Power Light will illuminate.
NOTE:
Avoid overloading your circuit by not
using other high wattage appliances in the
same outlet.
3. Operate heater by pressing the Power
Button (
) and selecting modes and
settings according to your preference.
– Power On/Off
Press the Power On/Off Button to turn the heater
on. Once on, the heater will run in the
Max
Heat
(
2
) mode and the
Stay On
temperature
indicator light will illuminate. Press the Power
On/Off button to manually turn off the heater at
any setting.
NOTE:
The Power Light will remain illuminated
while unit is plugged in.
Mode Selection
Select your desired heat settings by pressing the
corresponding buttons as located on your heater
to cycle through the heat settings. An indicator
light will illuminate next to each button to
indicate that the selected setting/mode is
activated.
– Fan Only Setting
Press the
Fan Only
Button to run the heater
without heat output. The
Stay On
temperature
indicator light will remain illuminated.
2 – HIGH Heat Setting
Press the
Max Heat
Button (
2
) to run the
heater continuously at 1500W. The
Stay On
temperature indicator light will remain
illuminated.
1 – LOW Heat Setting
Press the
Low Heat
Button (
1
) to run the
heater continuously at 750W. The
Stay On
temperature indicator light will remain
illuminated.
– Thermostat Control
Your heater is equipped with a digital thermostat
that allows you to set your heater to a precise
comfort level by turning the Dial Wheel.
To preset a precise comfort level, turn the Dial
Wheel to adjust the temperature from
21°C
to
30°C
. The corresponding
Temperature
Indicator
will illuminate once selected.
When the preset temperature is reached, the
heater will shut off and cool down for 15
seconds. When the room temperature drops
below the preset temperature, the heater will
automatically turn on again to maintain the
preset temperature level.
– Frost Guard Setting
To prevent frost, you may turn the Dial Wheel to
4
BCH9210-LA_10MLM1.indd 4
BCH9210-LA_10MLM1.indd 4
6/24/10 8:17 AM
6/24/10 8:17 AM
