background image

Mag HVLP autoMatic  

aiRSPRay gun

The following instructions provide the necessary 
information for the proper operation and preventive 
maintenance of the Binks MAG HVLP Manifold 
Mounted Airspray Gun. Please read and understand  
all information in this document in order to get the 
maximum performance from your new MAG HVLP 
airspray gun.

The automatic MAG HVLP gun is a conventional 
style airspray gun with special nozzle and 
modifications that allow it to operate at high transfer 
efficiencies in compliance with the “California South 
Coast Air Quality Management District” regulations 
as a “high volume, low pressure” airspray gun.

High pressure, low volume airflow is converted to 
high volume, low pressure within the gun body. 
Special air and fluid nozzle enable the gun to 
atomize fluid at low air pressure and velocities, 
creating the “soft spray” effect for high transfer 
efficiencies.

If you have any questions or do not understand the 
information presented, call your nearest service 
representative.

Part 

Sheet

77-2803R-11

SPecificationS:

Max. Air Pressure: 

 100 psi/6.8 bar

For HVLP compliance:   See page 5
Max. Fluid Pressure:   120 psi/8.3 bar
Min./Max. Cylinder   50 psi/3.4 bar (min.), 
Actuating Pressure:  100 psi/6.8 bar (max.)
Gun Body: 

 Stainless Steel, Aluminum 

Fluid Path: 

 Stainless Steel

Fluid Inlet and  
Outlet Size: 

 1/4" NPT(F) thread

Air Inlet Size: 

 Atomizing Air: 1/4" NPT(F) 
manifold body, 1/4" NPT x 
1/4" NPS(M) fitting (loose) 
Fan Air: 1/4" NPT(F)  
manifold body, 1/4" soc head 
plug (M) fitting (loose) 
Cylinder Air: 1/8" NPT(F) 
manifold body, 1/8" NPT x 
1/4" O.D. tube fitting (loose)

Gun Weight 

 

 

with Manifold: 

 2.8 lbs. (1.27 kg)

Gun Mounting Hole:  1/2" Dia.
The MAG HVLP is approved to ATEX level II 2 G X 
and is suitable for use in Zones 1 and 2.

Replaces 

Part Sheet 

77-2803R-10

notE

iMPoRtant ReGULatoRY note regarding the use of 

this product appears on page 6.

caution

Before removing any components from spray gun, 

shut off air and material pressure.

!

ii 2 G X

ca PRoP

65

PRoP 65 WaRninG
WARNING: This product contains chemicals known 
to the State of California to cause cancer and birth 
defects or other reproductive harm.

Содержание MAG HVLP 4006-1100-0









Отзывы: