2
toXic fLUid HazaRd
• Know the specific hazards of the fluid you
are using. this information is on the MSdS
for the material being used. Read all fluid
manufacturer warnings.
• Store hazardous fluids in approved
containers only. dispose of all hazardous
fluids in accordance with all state, local and
national guidelines.
• Wear the appropriate protective clothing,
gloves, eyewear and respirator.
equipment misuse can cause the equipment
to fail, malfunction, or start unexpectedly
and result in serious injury.
fiRe and eXPLoSion HazaRd
• Ground the equipment and object being
sprayed.
• Provide fresh air ventilation to avoid the
build up of flammable fumes from the
material being sprayed or from solvent.
• extinguish all open flames or pilot lights in
spray area.
• electrically disconnect all equipment in the
spray area.
• Keep the spray area free from all debris,
including solvent rags.
• if there is any static sparking while using
the equipment, StoP SPRaYinG
iMMediateLY. identify and correct the
problem.
eQUiPMent MiSUSe HazaRd
• this equipment is for professional use only.
• Read and understand all instructional
manuals, tags, and labels before operating
equipment.
• Use the equipment only for its intended
purpose. if you are unsure about its
purpose call your local Binks distributor.
• do not alter or modify this equipment. Use
only genuine Binks parts.
• do not exceed the maximum working
pressure of the lowest rated system
component. tHe MaXiMUM
RatinG of tHe MaG HVLP GUn iS 120 P.S.i.
do not eXceed tHe fLUid PReSSURe
RatinG.
• Route all hoses away from all sharp edges,
moving parts, hot surfaces and high traffic
areas.
• do not use hoses to pull the equipment.
• Use only Binks approved hoses.
• Use only solvents compatible with hoses
and wetted parts of the equipment used.
• comply with all applicable local, state and
national fire, electrical and other safety
regulations.
• improper grounding, poor air ventilation,
open flame or sparks can cause a hazardous
condition and result in fire or explosion and
cause serious injury.
noiSe LeVeLS
• the a-weighted sound level of spray guns
may exceed 85 dB(a) depending on the
setup being used. it is recommended that
ear protection is worn at all times when
spraying.
PRoP 65 WaRninG
• WaRninG: this product contains chemicals
known to the State of california to cause
cancer and birth defects or other
reproductive harm.
Warning
HiGH PReSSURe can caUSe SeRioUS injURY if
eQUiPMent iS inStaLLed oR USed incoRRectLY—
REad, undERStand, and obSERVE
aLL WaRninGS
and inStRUctionS in tHiS ManUaL.
oPeRate eQUiPMent onLY afteR aLL
inStRUctionS aRe cLeaRLY UndeRStood.
!
fLaMMaBLe, eXPLoSiVe and toXic VaPoRS
In this part sheet, the words
WaRninG
,
caUtion
and
note
are used to emphasize important safety information as follows:
caution
Hazards or unsafe practices which could
result in minor personal injury, product
or property damage.
!
WaRning
Hazards or unsafe practices which could
result in severe personal injury, death or
substantial property damage.
!
notE
important installation, operation or
maintenance information.
The automatic Spray Gun models listed in the following declaration of conformity may be used in some potentially explosive atmospheres
ONLY when the special conditions for safe installation and operation have been followed as expressed in this user manual (Part Sheet).
These models are approved to ATEX regulations 94/9/EC, protection level: ii 2 G X: Suitable for use in zones 1 and 2.
ec declaration of conformity
Manuf. By:
Finishing Brands
195 Internationale Blvd.
Glendale Heights, IL 60139
Type/Series:
Manifold Mounted Automatic Spray Guns
Model: MAG HVLP: 4006-, 4007-, 4008-, 4009-
The equipment to which this document relates is in conformance with the following standards or other normative references:
en iSo 12100-1&2:2003 and BS en 1953:1999 and thereby conform to the protection requirements of Council Directive 98/37/
EC relating to Machinery Safety Directive, and;
en 13463-1:2001, Council Directive 94/9/ec relating to equipment and Protective Systems for use in Potentially explosive
atmospheres, protection level ii 2 G X.
Approved By: _____________________________ Date: ____________
Chuck McCulloch, Finishing Brands
Finishing Brands reserves the right to modify equipment specification without prior notice.
April 17. 2006
