Binks MAG HVLP 4006-1100-0, Руководство пользователя

Страница: 5 / 8

HVLP aiR nozzLeS 90P
GUn nozzLe nozzLe
inLet aiR fLoW atoMizinG
PSI SCFM PSI
5.0 4.0 3.0
7.0 4.5 5.0
10.0 5.0 7.0
12.0 5.5 9.0
15.0 6.0 10.0
HVLP aiR nozzLeS 92P
GUn nozzLe nozzLe
inLet aiR fLoW atoMizinG
PSI SCFM PSI
6.0 4.5 3.0
8.5 6.0 5.0
11.0 6.8 7.0
13.5 7.5 9.0
15.0 8.0 10.0
HVLP aiR nozzLeS 93P
GUn nozzLe nozzLe
inLet aiR fLoW atoMizinG
PSI SCFM PSI
8.0 5.5 3.0
11.5 7.0 5.0
14.5 8.0 7.0
17.0 9.5 9.0
18.0 10.0 10.0
HVLP aiR nozzLeS 94P
GUn nozzLe nozzLe
inLet aiR fLoW atoMizinG
PSI SCFM PSI
14.0 7.0 3.0
21.0 9.0 5.0
27.0 11.0 7.0
30.0 12.0 9.0
33.0 13.0 10.0
HVLP aiR nozzLeS 95P
GUn nozzLe nozzLe
inLet aiR fLoW atoMizinG
PSI SCFM PSI
20.0 11.0 3.0
30.0 15.7 5.0
38.0 17.5 7.0
45.0 19.6 9.0
50.0 22.5 10.0
HVLP aiR nozzLeS 100P
GUn nozzLe nozzLe
inLet aiR fLoW atoMizinG
PSI SCFM PSI
3.0 3.2 2.0
6.1 4.8 4.0
9.0 6.0 6.0
11.6 6.9 8.0
14.3 8.0 10.0
PRoBLeM caUSe action
fluttering Insufficient fluid supply. Adjust fluid regulator or fill fluid
Spray Pattern supply tanks.
Air in paint supply line. Check and tighten pump siphon hose
connections, bleed air from paint line.
Striping Spray – Tip partially plugged. Clean or replace tip assembly.
fingers
irregular Pattern Fluid builds up on tip, or Clean tip.
tip partially plugged.
On defective side of pattern, air horn Clean air horn holes with solvent and
holes are plugged. a soft brush.
Pattern pushed to On defective side of pattern, air horn Clean air horn holes with solvent and
one side, same side holes are plugged. a soft brush or toothpick.
of air cap gets dirty
SPRaY PatteRn tRoUBLeSHootinG
fLUid nozzLeS—StandaRd nozzLeS
aiR nozzLe teSt GaUGe aSSeMBLY
5
caution
do not exceed 100 psi gun inlet pressure. Use air nozzle test gauge assembly to
determine and verify exact nozzle operating air pressure.
!
nozzLe and needLe SeLectionS—HVLP aiR nozzLe
Part fluid orfice Size orfice Size applicable
Material number nozzle no. (inches) (mm) air nozzle compatiable fluid needle
Ultra Light: 45-8900 89 0.020 0.5
90P, 92P, 93P,
54-5360 – "90PF" Feathering Delrin Tip Reduced Flow 45-8902 89A 0.025 0.6
94P, 95P
54-5365 – "90SF" Feathering S.S. Tip
Very Light:
45-9000 90 0.030 0.8 100P
Reduced Flow
Light: less than 15 to 20 45-9100 91 0.040 1.0
seconds in ZAHN 2 Cup, 45-9200 92 0.046 1.2 90P, 92P, 93P, 54-5370 – "AB" Delrin Tip 54-5375 – "ABSS"
e.g., stains, varnishes, 45-9400 94 0.055 1.4 94P, 95P Stainless Steel Tip
thin lacquers, automotive 45-9700 97 0.070 1.7 100P
refinishing materials.
Part no. description
54-3902 92P Nozzle
54-3935 95P Nozzle
54-4066 94P Nozzle
Part no. description
54-4345 90P Nozzle
54-4356 93P Nozzle
54-5650 100P Nozzle
59-299 GAUGE