108936BD_0812
6-1
REV E
ENGINE MAINTENANCE
General Engine Maintenance
Detailed instructions and recommendations for break-in and
regular maintenance are specified in the Engine Owner’s
manual. Please refer to this manual for engine servicing,
lubricating oil levels with quality and viscosity
recommendations, bolt torques, etc. The engine warranty is
backed by the engine manufacturer.
Engine Oil and Filter
Check engine oil daily and after every 4 hours of operation.
Machine must be setting level when checking oil. Refer to
engine manual and maintenance schedule for oil
recommendation and capacities.
Change the engine oil and filter after the first 5 hours of
operation and per the engine manufacturer’s recommendations
after that. If mower is being operated in extremely dirty
conditions, then it is recommended oil be changed more
frequently.
IMPORTANT:
When removing the oil filter take
precautions to minimize oil spillage on the exhaust system.
Draining the engine oil. (units equipped with oil drain
valve as shown in Figure 6-1).
1.
Locate the oil drain valve on the lower left side of the
engine.
2.
Remove the dust cap.
3.
Locate the oil drain hose that was supplied with the
machine. Be sure to clean and clear it of debris that might
block the flow of the engine oil.
4.
Attach one end of the hose onto the oil drain valve nipple.
Make sure the hose is pushed all the way onto the valve.
Figure 6-4
5.
Position the loose end of the hose out to the left side of
the mower so that it can drain into a suitable oil drain
container.
6.
With the hose in position, twist the valve
counterclockwise and pull out to open the valve. Allow
10 minutes for engine oil to adequately drain.
7.
After oil is drained, close the valve by pushing in on the
valve body and twisting it clockwise.
8.
Once the valve is closed, carefully remove the oil drain
hose and clean up any spilled oil.
IMPORTANT:
All oil drips or spills
must
be cleaned off
of the exhaust system before operating the machine.
9.
Re-install the dust cap on the oil drain valve nipple.
10.
Clean the oil drain hose and store it appropriately.
Engine Air Filter
Perform engine air filter maintenance per the
Maintenance
Schedule
shown elsewhere in this manual.
Cartridge type filter
A specially designed dry filter is standard equipment on some
BigDog
®
mowers which supplies clean combustion air to the
engine. An example of the air filter is shown in Figure 6-4.
Recommended service procedure
1.
Release clamps and remove element. Clean the canister
with a damp cloth.
2.
Before installing a new element, inspect it by placing a
bright light inside and rotate the element slowly, looking
for any holes or tears in the paper. Also check gaskets for
cuts or tears. Do not attempt to use a damaged element
WARNING
If the engine has been running and is up to operating tem-
perature, allow the engine to cool before changing the oil.
Engine and engine oil will be very hot, so be very careful
when changing oil and wear the appropriate protective
gear to avoid being burned or exposed to engine oil.
Figure 6-1
Figure 6-2
Oil drain valve
Oil drain hose
Содержание Series X
