10
1. ASSEMBLY INSTRUCTIONS.-
Take the unit out of its box and make
sure that all of the pieces are there
Fig.1.
(1) Main body; (8) Handlebar stem;
(22) Saddle post; (23) Saddle; (15)
Handlebar; (24) Monitor; (3) Rear
stabiliser bar; (2) Front stabiliser bar; a
box containing the following: (4) Slot
head bolts M-10x105; (5) Curved
washer M-10; (6) Cap nut M-10; (13)
Curved washer M-8; (14) Allen screw;
(16) Handlebar bracket; (17) Allen
screw M8x20; (18) Bracket cover; (19)
Handlebar lever; (20)
Flat washer M-8;
(21) Saddle post knob; (28) Left pedal;
(29) Right pedal.Allen key; Double
ended ring spanner; Pedal spanner.
2.
Take the rear stabiliser bar (3) and
position it on the machine’s rear stand
bracket, as shown in Fig.2, inserts
bolts (4), fit the curved washers (5) the
cap nuts (6) and tighten securely.
Take the front stabiliser bar with
wheels (2) and position it so that the
two red dots (A) line up, as shown in
Fig.2, insert bolts (4), fit the curved
washers (5) the cap nuts (6), and
tighten securely.
3. FITTING THE HANDLEBAR.-
Bring the handlebar (15) up to the
handlebar stem (8), Fig.3, insert the
hand-grip cable (26) in through the
slot as shown in Fig.3A and 3B, and
pull it out through the top of the
handlebar stem. Fit the handlebar
bracket (16), insert screw (17) and
hand tighten, put the washer (20) on
and the handlebar lever (19), position
the handlebar and tighten gently, then
fit the bracket cover (18).
4. FITTING THE MONITOR.-
Take the monitor (24) and remove the
four screws (25) from the base of the
monitor, Fig.4, connect the terminals
for the feedback cables (30) coming
out of the monitor to the cable (9)
sticking up out of the handlebar stem,
Fig.4, then plug the terminal (26)
which is also sticking out of the
handlebar stem into the hole (31) on
the base of the monitor, position the
monitor on the handlebar stem,
making sure not to catch any of the
cables, and attach it using the four
screws (25) removed previously.
5. FITTING THE HANDLEBAR
STEM.-
Hold the handlebar stem (8) and
connect the feedback cable terminals
(9) and (10), Fig.5. Take the tension
cable (11) from the handlebar stem (8)
and connect it to the bottom tension
support (12), as shown in Fig.5A.
Insert the handlebar stem (8) onto the
boss on the main body (1) in the
direction of the arrow, making sure not
to catch any of the cables, and check
that the tension control (11) works
correctly. Next, line up the handlebar
stem with the holes and fit the 3 Allen
screws (14) and the curved washers
(13), tighten securely.
6. ATTACHING THE SADDLE.-
Place the saddle (23), Fig.6, onto the
saddle post (22), as shown in Fig.6,
bearing in mind that the holes on the
saddle post go at the front section of
the saddle, position the saddle
correctly and tighten nuts (87)
securely.
Содержание Bio Bike H6716
Страница 2: ...2 Fig 1 Fig 2 Fig 3 ...
Страница 3: ...3 Fig 4 Fig 5 Fig 6 Fig 7 ...
Страница 4: ...4 Fig 8 Fig 9 ...
Страница 33: ...33 H6716 ...