Best Barns Greenbriar II 12x16 Скачать руководство пользователя | Manualshive

Страница: 10 / 20

background image

1.

Install a gable frame centered on the back wall. Gable plate should be

flush with filler. NOT over OSB. Secure with 10d sinkers.

2.

Install the gable frame on the front wall.

Step 8

Install Primed Soffit and Fillers

Side

Wall

Flush with

Inside of 2x4

4.

Repeat to install soffit on the opposite side wall.

5.

Install (3) three 3-1/2" wide x 48-3/4" filler panels over the front and back wall.

Cut the last filler to fit between the soffit on the sidewalls.

Front Wall

Door Opening

7" Soffit

3-1/2" Filler

Step 9

Install Roof Gables

Tongue Edge

Flush

1.

Install a 7" wide x 48-3/4" siding panel over the side wall with the primed side facing down.

The 'tongue' edge should be flush with front wall plate, NOT over OSB. Tack the soffit with
a couple 6d common nails. Installing 2x4 tie plates in a later step will provide more nailing.

2.

Install (3) three more siding panels. Cut the last soffit flush with the 2x4 wall plate.

«
...
8
9
10
11
12
...
»

Содержание Greenbriar II 12x16





















Отзывы:

Нет отзывов

Похожие инструкции для Greenbriar II 12x16

01OVLPA0305SDNW-V1

Бренд: Mercia Garden Products Страницы: 6

Бренд: Palmako Страницы: 29

LILLEVILLA SEILI

Бренд: Luoman Страницы: 40

LILLEVILLA Liekune

Бренд: Luoman Страницы: 48

DUOTECH OAKLAND 757

Бренд: Keter Страницы: 44

OAKRIDGE 8 x 12

Бренд: Yardline Страницы: 88

Бренд: Palmako Страницы: 43

Бренд: Palmako Страницы: 101

GS84-SLIDER-METAL-AK

Бренд: OLT Страницы: 38

Бренд: Palmako Страницы: 61

Pavilion PAV44-3838

Бренд: Palmako Страницы: 59

Бренд: Shire Страницы: 3

Бренд: Bear County Страницы: 16

SunShed SSGS1216-FJ-Cedar

Бренд: OLT Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды