background image

X

X

X

X

X

X

X

X

X

X

Step 4

Assemble Front Wall Frame

6.

Cut a 4'x8' OSB panel in half creating (2) two 2'x8' panels. Install one panel flush with the

side of the door opening and flush with the 2x4 top plate. Use 6d common nails.

7.

Locate (2) two 20"x 48" OSB panels and install above the door opening. Install flush with top

plate. Cut the siding flush with bottom of header.

nail

nail

144" Treated Bottom Plate

3.

Remove (2) two 2x4s screwed

to the pallet. Cut both to a
length of 82" and install as
header supports where shown.
Nail to stud using 10d sinkers.

4.

Install the door header on the

header supports. Nail to the
wall stud with 10d sinkers.

5.

Measure space between

header and top wall plate. Cut
(5) five pieces to this length
from a pre-cut wall stud.
Install these evenly spaced
above header with 10d sinkers.

2x4 Block

Centered

2x8 Door Header

2.

Install (4) four pre-cut wall studs between the wall plates where shown. Nail top plate to studs

using 10d sinkers. Nail bottom plate to studs using 16d galv. nails.

8.

Install 2'x8' siding panel on the right

side of the wall panel.

1.

Cut (2) two 2x4-12' boards (one will be treated) to a length of 144" for wall plates. Position

the boards together and indicate with 'X' Marks where the wall studs will be located

96" Finished Door Opening

21"

21"

Treated Bottom Plate

Cut OSB Flush

Flush

82" Header Support

96" Door Opening

Содержание Greenbriar II 12x16





















Отзывы: