Besantek BST-CBF01 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 26

Besantek BST-CBF01 Скачать руководство пользователя страница 10

-8-

AUTO-OFF

The sniffer has an Enser-Save auto-off timer which

run from the time the sniffer has been turned ON.

After auto-off, the user will need to switch the Sniffer

ON again, if he wants to use it. The auto-off can not

be over-riden by the signal strength. The Auto-off

timer start counting down since the On key has been

depressed.

POWER ON INDICATOR

The Power On indicator Led is a dual Indicator.

When the tester is turned ON, this indicates;

- the tester has been turned on.

- the healthy condition of the battery.

BATTERY OK INDICATOR

As for the Power ON Indicator, the same Led

indicates that the battery voltage is enough to make

tests. Should the battery need replacement, the led

will turn off, even if the bar-graph still works.

LED BAR-GRAPH

The Signal Strength is shown on the Leds bar-graph.

The more Leds ON, the more the signal strength.

The circuit to find is likely to be the one with the most

LEDs lightning up.

«
...
8
9
10
11
12
...
»

Содержание BST-CBF01



























Отзывы:

Нет отзывов