manualshive.com logo in svg

Besam PowerSwing, Руководство по установке

Поделиться
Скачать
Besam PowerSwing Скачать руководство пользователя страница 20

PowerSwing    US23-0922-02

20

© Copyright 2006 Besam Entrance Solutions. May not be reprinted or reproduced without permission. 

Mechanical Installation, PULL/PULL-P

Mounting the Drive Arm and Door Fitting, PULL/PULL-P

Note

!  For installation of PULL-P (panic break-out) see also illustration (drawing 

No. 655990) page 21.

1.  Connect the main power (see page 21).
2.  Open the door to an angle of 90°.
3.  Give constant impulse by strapping the impulse inputs on the control unit. The 

drive shaft turns to a factory-set position. 

4.  Slide the guide shoe into the door fi tting.
5.  Using dimensions shown from hinge center line, mount the door fi tting to the 

door panel fastening securely.

6.  Mount the drive arm on the drive shaft with the door in unchanged position 

(90°). Ensure that the teeth of the adaptor fi t well with the operator drive shaft 
and the drive arm. 

7.  Tighten the screw to a torque of 25 Nm (19 lbf . ft).
8.  Slide the arm stop against the guide shoe and then back 20 mm (3/4"). The 

guide shoe must not hit the arm stop during normal operation. Fasten the arm 
stop. 

9.  Remove the strapping. The motor turns off and the door closes.

10.  Snap on the end plates to the door fi tting.

Checking the Door Movement

Push the door to its fully open position. Check that it can open to the required 
angle and that the guide shoe runs easily in the track of the door fi tting. Check also 
that the complete arm system operates without problems.

10-21-2002

Содержание PowerSwing













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды