Bertazzoni TUS95L 22 D X La Germania, Инструкция по установке, обслуживанию и эксплуатации

Страница: 12 / 48

12
f i nished, an acoustic interval signal sounds and the Bell symbol flashes.
The minute minder program runs i ndependently of other programs.
Key Lock
After power on reset or when no key is pressed for 7 seconds, the key look function is act i vated. Pressing a valid key or key
combination for 2 seconds or more will deactivate the key lock.
USING THE ANALOG CLOCK (Fig.34)
For setting up the time displayed by watch pointers push briefly twice the knob till getting the CLOCK icon flashing.
For increasing or decreasing time displayed 1 minute by 1, turn the knob clockwise or counterclockwise, le minutes pointer will
increase or decrease 1 minute by minute clockwise or counterclockwise.
10 seconds after last set up the electronic timer will exit time set up mode.
Minute minder set up will activate a simple alarm when set up time is over.
For setting up an alarm push briefly once the knob till getting ALARM icon flashing. The turn the knob, set up the alarm time and
briefly push once the knob to confirm; ALARM icon will stay on for all the set up time. When set up time is over an acoustic buzz
will be activated. Push again briefly once the knob for going back to time display.
For cancelling minute minder set up keep the knob pushed until ALARM icon goes off.
CLEANING THE APPLIANCE
Before cleaning the appliance, it should be disconnected from the power supply and turn off the main gas feeder valve.
Cleaning the work surface:
Periodically clean the burner heads, the enamelled steel grids, the enamelled covers and the flame caps using warm soapy
water. Then those parts should be rinsed and thoroughly dried.
Any liquid that overflows from pots must always be removed using a rag.
If it becomes difficult to open or close a valve, do not force it, but immediately request the assistance of the technical
service personnel.
Cleaning the enamelled parts:
To maintain the original features of the enamelled parts they should be cleaned frequently with soapy water. Never use abrasive
powders. Do not leave acidic or alkaline substances on the enamelled parts (vinegar, lemon juice, salt, tomato sauce, etc.) and
do not wash the enamelled parts while they are still hot.
Cleaning the STAINLESS steel parts:
Clean the parts with soapy water and then dry them with a soft cloth. The shine is maintained by periodically using special
products that generally are found in the market. Never use abrasive powders.
Cleaning the burner flame caps:
Since the flame caps are resting on the burner, to clean them just remove them from their seat and wash them with soapy
water. After they have been thoroughly dried and having checked that the holes are not clogged, they can be replaced in their
proper position.
Oven door with glass screwed:
Cleaning the inside of the oven glass:
One of the features of the oven is the possibility of removing the interior glass simply by loosening the 2 screws
B
(see fig. 35-
36), to clean the inside surface of the glass. This operation should be carried out while the oven is cold and with a damp cloth.
Do not use abrasives.
Cleaning the inside of the oven:
To thoroughly clean the inside of the oven, it is recommended to disassemble the door by carefully following the instructions
described below. Insert the hook
C
(figure 37) into the hinged sector
D
. Put the door in a semi-open position and using both
hands pull it towards you until it is released from the attachment. To replace the door, do the opposite making sure to insert the
two sectors
F
correctly. In addition, the side shelves can be removed very easily, by loosening the lock rings that attach them to
the oven.
Oven door with glass stuck:
Cleaning the inside of the oven glass:
Cleaning the interior of the crystals of the oven:
Feature of the oven is the ability to remove the inner glass in order to make the internal cleanliness of crystals. This operation is
to be performed in a cold oven and with a damp cloth, taking care not to use abrasive detergents. For the removal of internal
glass lock the hinges by inserting the nail that came in the hinges (Fig 38-39) then remove the inner glass as (Fig.40-41-42-43-
44-45).
To reassemble the door to perform tasks in the opposite direction as (fig.46-47-48-49).
Cleaning the inside of the oven:
To facilitate intensive cleaning of the oven is practical to dismantle the door by following the instructions listed below. Insert the
nail that came in the hinges (Fig. 3
8
-3
9
). Bring the half-open door in place and working with your hands pull the door towards
you until the same has not been dropped from the attack. To replace the oven door proceed in reverse order. Also the grids side
are easily-removable by unscrewing the rings that secure it to the oven.
AFTER-SALES TECHNICAL SERVICE
AND SPARE PARTS
Before leaving the factory, this appliance was tested and calibrated by skilled and qualified personnel.
Any repairs or calibration that may become necessary after leaving the factory should be performed by skilled personnel.For this
reason we advise the customer to contact the Dealer that sold the appliance or the nearest Service Centre, providing them with
information about the type of appliance and the type of problem that has occurred.If defective parts must be replaced, it is
recommended to replace them with original spare parts that are available only in our technical Service Centres and authorised
dealers.