BERGHOF DC1000 Скачать руководство пользователя страница 5

Страница: 5 / 142

USER MANUAL 1.10 | DC1000 DIALOG-CONTROLLER

Berghof Automation GmbH | Harretstrasse 1 | 72800 Eningen | www.berghof.com
DC1000_HB_en_2D0982010ZD00.docx

Contents

GENERAL ............................................................................................................................................ 9

1.1.

About this manual .............................................................................................................................. 9

1.2.

Hazard categories and terminology ................................................................................................ 10

1.3.

Qualified personnel .......................................................................................................................... 11

1.4.

Due diligence .................................................................................................................................... 11

1.5.

Basic safety measures ..................................................................................................................... 12

1.6.

Use as prescribed ............................................................................................................................ 13

1.7.

Conformity declaration .................................................................................................................... 14

1.7.1.

Extension modules ............................................................................................................................. 14

1.8.

Transport and setup ......................................................................................................................... 15

PRODUCT DESCRIPTION ................................................................................................................ 17

2.1.

Identification ..................................................................................................................................... 19

2.2.

The different versions of the Dialog-Controller ............................................................................. 20

2.2.1.

Interfaces ........................................................................................................................................... 20

2.2.2.

Front foil sheeting ............................................................................................................................... 20

2.2.3.

Overview of types ............................................................................................................................... 21

2.2.4.

Variable thanks to extension cards ..................................................................................................... 21

2.3.

Dialog-Controller DC1005 / DC1010 / DC1012 construction ........................................................ 22

2.3.1.

Block circuit diagram .......................................................................................................................... 22

2.4.

Technical data DC1005 .................................................................................................................... 23

2.4.1.

DC1005 Front view ............................................................................................................................. 25

2.4.2.

DC1005 Rear view ............................................................................................................................. 25

2.4.3.

DC1005 Dimensions .......................................................................................................................... 26

2.4.4.

DC1005 Panel cutout ......................................................................................................................... 27

2.4.5.

Mounting regulation DC1005 .............................................................................................................. 27

2.5.

Technical data DC1010 .................................................................................................................... 28

2.5.1.

DC1010 Front view ............................................................................................................................. 30

2.5.2.

DC1010 Rear view ............................................................................................................................. 30

2.5.3.

DC1010 Dimensions .......................................................................................................................... 31

2.5.4.

DC1010 Panel cutout ......................................................................................................................... 32

2.5.5.

Mounting regulation DC1010 .............................................................................................................. 32

2.6.

Technical data DC1010 Compact (CP) ............................................................................................ 33

2.6.1.

DC1010 Compact (CP) front view ...................................................................................................... 35

2.6.2.

DC1010 Compact (CP) rear view ....................................................................................................... 35

2.6.3.

DC1010 Compact (CP) dimensions ................................................................................................... 36

2.6.4.

DC1010 Compact (CP) panel cutout .................................................................................................. 37

2.6.5.

Mounting regulation DC1010 Compact (CP) ...................................................................................... 37

2.7.

Technical data DC1012 .................................................................................................................... 38

2.7.1.

DC1012 Front view ............................................................................................................................. 40

2.7.2.

DC1012 Rear view ............................................................................................................................. 40

2.7.3.

DC1012 Dimensions .......................................................................................................................... 41

2.7.4.

DC1012 Panel cutout ......................................................................................................................... 42

Содержание DC1000















































































































































Результаты поиска

Содержание DC1000

Отзывы:

Похожие инструкции для DC1000

Бренды по названию

Популярные бренды

BERGHOF DC1000, Руководство пользователя

Результаты поиска

Содержание DC1000

Отзывы:

Похожие инструкции для DC1000

Бренды по названию

Популярные бренды