Bercomac BERCO PIONEER 700455 Скачать руководство пользователя страница 23

Страница: 23 / 34

TROUBLESHOOTING

(For identification, see the parts breakdown)

PROBLEM

POSSIBLE CAUSES

CORRECTIVE ACTION

Snowblower is noisy.

NOTE

Please

note

this

snowblower may appear to be

noisy.

New chain and new sprocket.

Lubricate the roller chain.

NOTE:

When snowblower is new it is

louder, the noise will decrease over

time.

Snowblower vibrates or is

abnormally noisy.

Damaged pulley.

Replace pulley.

Damaged bearing.

Replace bearing.

Damaged fan.

Dismount & repair or replace fan.

Auger bent.

Replace auger.

Auger stopped turning.

Shear bolt broken.

Replace shear bolt. Also see

"Maintenance" section.

Chain broken or connecting link

unlocked.

Remove chain guard. Inspect and

repair if needed.

Snowblower stopped turning.

The belts are damaged or snapped.

Check & replace damaged belts.

Belt is worn at a specific point.

Snowblower was engaged when

already plugged.

Make sure auger & fan are not

plugged or frozen before engaging

snowblower.

Lack of tension on the belt.

Replace the tension spring if it has

lost its efficiency.

Belt showing premature wear.

Spring stretched.

Check spring. Replace if stretched.

Engine is misaligned

Realign the engine.

Chute rotation is difficult.

Dirt or ice may be underneath chute.

Clean the base of chute & the

rotation ring.

Lubricate chute inside & out and the

rotation worm.

The base of the chute may be

damaged or bent.

Clean parts, lubricate & reinstall.

Make sure the retaining plates are

not too tight on the chute base, it may

be a reason why the chute is not

turning freely.

Содержание BERCO PIONEER 700455



































Результаты поиска

Содержание BERCO PIONEER 700455

Отзывы:

Похожие инструкции для BERCO PIONEER 700455

Бренды по названию

Популярные бренды

Bercomac BERCO PIONEER 700455, Руководство пользователя

Результаты поиска

Содержание BERCO PIONEER 700455

Отзывы:

Похожие инструкции для BERCO PIONEER 700455

Бренды по названию

Популярные бренды