Bell OH-58 C Скачать руководство пользователя страница 256

Страница: 256 / 333

TM 55-1520-228-BD

ENVIRONMENTAL CONTROL SYSTEM

PROCEDURAL STEPS:

Stop drill any cracks which might be

extending from hole.

Locate damaged area and remove

panels and/or other items as necessary

Sand both the bottom surface of the

to gain access to the duct to be

patch and the surface area around the

repaired.

Refer to Figures 15-2 and

hole to be covered by the patch.

15-3 for locations of rigid plastic

ducts.

Clean surface with solvent.

Cut a patch out of sheet stock.

6. Apply sealant to patch and on the

surface area that will be covered by the

Tape into place.

patch.

Record BDAR action taken. When

mission is complete, as soon as

practical, repair the equipment/system
using standard maintenance procedures.

OPTION 2: Hole or Crack in Duct, Rigid
Plastic.

Press patch in place, and wrap glass

tape around patch and duct to hold the

repair in position.

Record BDAR action taken. When

mission is complete, as soon as

practical, repair the equipment/system

using standard maintenance procedures.

LIMITATIONS:

Inspect after every flight.

15-6.

FLEXIBLE DUCT DAMAGE.

PERSONNEL/TIME REQUIRED:
1 Soldier

1 Hour

MATERIALS/TOOLS REQUIRED:

0.016 inch Sheet Metal Minimum
Sealant (item 4, Appx C)
400 Grit Sand Paper (item 45, Appx C)
Cleaner Naptha or Equivalent

(item 7, Appx C)

Glass Tape or Aluminum Tape

(item 60, Appx C)

PROCEDURAL STEPS:

Locate damaged area and remove

panels and/or other items as necessary
to gain access to the duct to be

repaired.

Refer to Figures 15-2 and

15-3 for locations of rigid plastic

ducts.

Cut a patch out of sheet stock.

Patch should extend 1-1/2 inches from
the edge of the hole at all points.

GENERAL INFORMATION: The flexible ducts
are composed of special wire covered

fabric with impregnated rubber.

LIMITATIONS:

These repairs are tem-

porary and the damaged hoses should be

replaced as soon as possible.

Inspect

after every flight.

PERSONNEL/TIME REQUIRED:
1 Soldier
15 Minutes

MATERIALS/TOOLS REQUIRED:

Glass Tape or Equivalent

PROCEDURAL STEPS:

Locate damaged area and remove panels

and/or other items as necessary to gain
access to the duct to be repaired.

Refer

to Figures 15-2 and 15-3 for locations of
flexible plastic ducts.

15-8

Содержание OH-58 C














































































































































































































































































































































Результаты поиска

Содержание OH-58 C

Отзывы:

Бренды по названию

Популярные бренды

Bell OH-58 C, Техническое руководство

Результаты поиска

Содержание OH-58 C

Отзывы:

Бренды по названию

Популярные бренды