Bell OH-58 C Скачать руководство пользователя страница 163

Страница: 163 / 333

Record BDAR action taken. When

mission is complete, as soon as

practical, repair the equipment/system
using standard maintenance procedures.

OPTION 2:

Replace Hose Section with MS

Fittings (no BDAR hose assemblies
available).

For Teflon and rubber hose.

LIMITATIONS: None.

PERSONNEL/TIME REQUIRED:

1 Soldier
30 Minutes

MATERIALS/TOOLS REQUIRED:

Replacement Section of Hose or Tube

(if needed)

Masking Tape (item 52, Appx C)
Fine Toothed Hacksaw

MS Fittings (socket, sleeve, and

female fitting, 4 ea.)

MS Union (2 ea.)

PROCEDURAL STEPS:

Cut out damaged hose section. Wrap

masking tape (or other available tape)

around hose over the areas where cuts
are to be made to contain the braided

wires from unraveling.

Mark on tape

where the cuts are to be made. Hold in

a vice and cut with a fine-toothed

hacksaw.

Take care to make square cut.

Do not remove tape.

NOTE

If the damage is small, the
length of a single union may be

sufficient to provide a repair.
However, if the damage is longer,

a replacement section will be

required.

Obtain the proper sized MS fitting

and unions.

3. Slip the MS socket over one of the
undamaged ends of the hose, Figure 9-12.
Use care not to unravel the wire braids.

TM 55-1520-228-BD

HYDRAULIC

Insert the MS sleeve between the

wire braid cover and the inner rubber

hose. Force onto hose until the edge of
the sleeve is even with the end of the

rubber hose.

Reem inside end of Teflon hose with

a square tool or a wooden plug so that
edge is smooth and flared to facilitate

insertion of the nipple of the MS female
fitting.

6. Slide the MS socket over end of hose

as far as it will go and hold in vise.

Insert nipple of MS female fitting into
rubber inner tube, Figure 9-13. Force

all the way until threads in socket and

female fitting together and tighten
until the gap between the edge of the

socket and the base of the female
fitting is approximately 0-1/32 inch for

rubber and 0.025 to 0.045 inch for

Teflon.

Prepare the other damaged end of the

hose in the same manner.

If no replacement section is

necessary, connect the MS fittings on
the undamaged ends with an MS union,
Figure 9-14.

If a replacement section is needed,

obtain replacement section and cut to
desired length.

Refer to step 1 for

procedure for cutting hose. No harm

will be done if replacement section is

too long.

Attach MS fittings to both

sides of the replacement section.

10.

Place replacement section between

the undamaged ends and connect the MS
fittings on the undamaged ends to the
fittings on the replacement section
using MS unions.

11.

Record BDAR action taken. When

mission is complete, as soon as

practical, repair the equipment/system

using standard maintenance procedures.

9-11

Содержание OH-58 C














































































































































































































































































































































Результаты поиска

Содержание OH-58 C

Отзывы:

Бренды по названию

Популярные бренды

Bell OH-58 C, Техническое руководство

Результаты поиска

Содержание OH-58 C

Отзывы:

Бренды по названию

Популярные бренды