Bell OH-58 C Скачать руководство пользователя страница 24

Страница: 24 / 333

TM 55-1520-228-BD
GENERAL INFORMATION

1-7.

WAIVER OF PRECAUTIONS. Under

combat conditions, BDAR may be performed
on helicopters which are in flight or

which are under power while on the
ground.

While some of these BDAR actions

may require waiving of safety precautions,

the cautions to protect personnel life
should not be overlooked.

Other similar

precautions may be waived at the discre-
tion of the commander.

BDAR fixes may

be required in a chemically toxic environ-

ment or under other adverse battlefield

conditions with severe limitations in

personnel, facilities, equipment, and

materials.

Performance of repair tasks

may be necessary while wearing protective

gear.

Decontamination procedures are

described in FM 3-5.

OPERATING CHARACTERISTICS. This

manual covers expedient repairs for the
OH-58 helicopter and its components. It

is entirely possible that in a combat

situation, the helicopter having under-

gone one or more repairs may suffer
degradation of its normal operating

characteristics (e.g., reduced speed,
reduced load capability, reduced range,
etc.), and still be able to carry out

all or parts of an assigned mission.
The minimum functional combat capability

(MFCC) criteria for the OH-58 is as

follows:

Flight Capability for Mission

Completion.

Helicopter’s flight charac-

teristics degraded to a minimum of
combat capable (CC).

(1) Sufficient power delivered to

main and tail rotor to accommodate lift

(4) Communications. Must have

intercom communications within aircraft

and at least two tactical receiver-

transmitter (R-T) units operating at
full capability.

NOTE

Criteria may be waived for

recovery or if the tactical
situation demands otherwise.

Flight Capability for

Self-Recovery Capability (SRC).

(1) Must have power delivered to

main and tail rotor at acceptable

limits.

(2) Maximum engine torque:

80% at 0 kts
64% at 16 kts
53% at 32 kts
50% at 50 kts

(3) Lift capability for crew

members. Unload unnecessary weight.

(4) Flight controls at minimum

function level acceptable for flight.

(5) Instruments/avionics as

required to meet mission needs.

(6) Maximum airspeed of 50 kts.

(7) Maximum flight duration of

2 hours.

Consideration will be given

to minimize flight duration.

capability for helicopter crew and cargo.

(8) Be prepared for emergency

procedures.

See TM 55-1520-228-10,

(2) No fuel leaks which will cur-

Chapter 9.

tail the intended length of flight.

(3) No degradation of any com-

ponent/system which will end in failure
and curtailment of intended mission.

1-4

1-8

Содержание OH-58 C














































































































































































































































































































































Результаты поиска

Содержание OH-58 C

Отзывы:

Бренды по названию

Популярные бренды

Bell OH-58 C, Техническое руководство

Результаты поиска

Содержание OH-58 C

Отзывы:

Бренды по названию

Популярные бренды