Bell System Bellcall Скачать руководство пользователя | Manualshive

Страница: 18 / 46

background image

Bellcall Digital Door Entry System

PD-083 Issue 3A

Installation and Operating Manual

Page 18 of 46

Programming the Panel – BSD-DIG

The BSD-DIG is programmed from the panel for all settings.

Security

It is strongly recommended that the Panel Security Code (PSEC) be changed from its
factory setting to prevent unauthorised access. Record the new number carefully as it
cannot be easily changed if lost. It is also recommended that the Phone Programming
Code (PPRG), Coded Access Code (ACOD) and Trades Access Code (TCOD) are all
changed from default even if not used.

To access panel programming without the code requires physical access to the controller
PCB, borrow a jumper from say video gain (remember the setting) and place it on the 5 pin
programming header between pins 1 & 2. Now pressing the test button will enter panel
programming for 30S when the panel security code can be read or set.

When the

programming is finished replace the jumper back to its original location.

Panel Programming

To use Panel Programming Mode :-



First type the Panel Security Code (initially 3434) followed by the

call

button.



The display will show the first programmable parameter (ACOD), and then alternating
at 1S intervals will be the data and the parameter name.



Press the

door

button to step down through the programmable parameters.



Press the

reception

button to step up through the programmable parameters.



The list rolls over bottom to top and vice versa.



To change a numeric parameter simply type a new 1-4-digit value and then press

call

.



To change other values simply press

call

to choose the next value.



To exit Panel Program Mode press

cancel

.



If no button is pressed for 30S then programming mode will auto-cancel.

Code

Default Access Description

ACOD

1234

Coded access code – must be 4 digits

TCOD

6789

Trade access code – must be 4 digits

LTIM

0003

Lock Time: 1-99 seconds

LOCK

Secr



Lock Type: Secr (fail secure), Safe (fail safe)

CAM2

No

Camera 2: No (absent), Yes (present)

TRAD

0005

Trade Function: 0-9 – see table

DMON

Cwo

Door Monitor Polarity: Cwo, Owo

RECP

9898

Reception / Porter phone number

PSEC

3434

Panel security code

PPRG

1212

Phone programming security code

RING

0015

Ring Time – see table

TALK

0015

Talk Time – see table

TONE

Both



Ring and Lock Buzz-Tone enable, 4 settings

CANC

Yes

Allow

Cancel

button to terminate Call

BCAL

No

Bellcall BCP1 compatibility mode

12A?

No

Allows user entry of 12A to call BSC4 output 13

«
...
16
17
18
19
20
...
»

Содержание Bellcall















































Отзывы:

Нет отзывов

Похожие инструкции для Bellcall

Univerge SV8100

Бренд: NEC Страницы: 8

Univerge SV8100

Бренд: NEC Страницы: 19

Univerge SV8100

Бренд: NEC Страницы: 9

Бренд: Samsung Страницы: 2

Бренд: Chamberlain Страницы: 4

FortiVoice 50E6

Бренд: Fortinet Страницы: 22

DTH-4R-2 - CORDLESS Lite II BLAC

Бренд: NEC Страницы: 57

Бренд: GE Страницы: 18

Compact ICS 7.1

Бренд: Nortel Страницы: 266

Port-O-Rotary Phone

Бренд: Sparkfun Electronics Страницы: 2

Бренд: TMC Страницы: 91

Бренд: Serene Страницы: 30

Бренд: 3Com Страницы: 130

Бренд: KAPSCH Страницы: 78

Бренд: Sony Страницы: 8

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 6

Бренд: Sony Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды