Belden GRASS VALLEY ADX-1901 Скачать руководство пользователя страница 42

Страница: 42 / 49

GUIDE TO INSTALLATION AND OPERATION

| ADX-1901

6 Specifications

Analog Audio Outputs (8)

Signal:

balanced analog audio

Impedance:

< 60

Max. level:

+24 dBu / 2 K

Audio Processing Performance

Quantization:

24 bits

Sampling:

48 kHz

Audio latency:

0.967 ms at 48 kHz

Audio delay:

Up to 2.7s (1 ms steps and 1 sample steps)

SNR:

>116 dB A weighted

0 dBFS:

0 to +24 dBu (1 dB steps)

Distortion:

<-90 dB (20Hz to 5 kHz)

Crosstalk:

<-110 dB (20 Hz to 20 kHz)

Freq. response:

± 0.05 dB (20 Hz to 20 kHz)

Tone generator:

-18 dBFS 1 kHz sine wave interrupted on left channel (250 ms) per EBU
R49

Video Input / Output

Signal:

SMPTE 259M-C (270 Mb/s)

SMPTE 292M (1.485, 1.485/1.001 Gb/s)

SMPTE 424M (2.970, 2.970/1.001 Gb/s)

Supported formats:

SD: SMPTE 259M: 480i59.94, 576i50

HD: SMPTE 274M: 1080i59.94, 1080i50, 1080p23.98, 1080psf24,

1080p25, 1080p29.97

HD: SMPTE 296M: 720p59.94, 720p50, 720p23.98, 720p24

3G: SMPTE 425M Level A (mapping 1), Level B: 1080p59.94, 1080p50

Embedded audio:

SMPTE 272M (SD), SMPTE

299M (HD)

Embedded ATC:

SMPTE RP188

Embedded ANC:

SMPTE 291M

Cable length:

SD: 400 m (1,312 ft.) Belden 1694A at 270 Mb/s

HD: 200 m (656 ft.) Belden 1694A at 1.485 Gb/s

3G: 100 m (328 ft.) Belden 1694A at 2.970 Gb/s

Input impedance:

75 Ω

Return Loss:

>15 dB up to 1.5 GHz

>10 dB from 1.5 GHz to 3 GHz

Jitter:

HD/SD: < 0.2 UI

3G:

< 0.4 UI

Video Processing

Signal Path:

10 bits

Video latency:

SD < 2.5 µS

HD, 3G: < 1 µs

Содержание GRASS VALLEY ADX-1901


















































Результаты поиска

Содержание GRASS VALLEY ADX-1901

Отзывы:

Похожие инструкции для GRASS VALLEY ADX-1901

Бренды по названию

Популярные бренды

Belden GRASS VALLEY ADX-1901, Руководство по установке и эксплуатации

Результаты поиска

Содержание GRASS VALLEY ADX-1901

Отзывы:

Похожие инструкции для GRASS VALLEY ADX-1901

Бренды по названию

Популярные бренды