manualshive.com logo in svg

Belden 934 840 001, Техническое руководство, Страница: 45 / 105

Поделиться
Скачать
Belden 934 840 001 Скачать руководство пользователя страница 45

Starting operation

Technical manual  LioN-P PROFINET IO-Link Master

Release 2.0 04/2017

6.4 Configuration of the LioN-P PRO-

FINET I/O modules in STEP 7

45

Upload only (device to master):

Enables the parameter data upload function to the IO-Link master from 
the device.

An upload is performed when an IO-Link device is connected and the 
master does not have any valid data. This is the case if "Disabled and 
Cleared" mode was configured previously and/or in case of "Disabled" 
in as-delivered condition.

If parameter data are changed on the device during runtime, the 
device data stored on the master can be overwritten using the 
ParamDownloadStore (Index 0x0002, Subindex 0x00, Value 0x05) 
command. This command sets the DS_UPLOAD_REQ flag on the 
device, and thus executes an upload.

The IO-Link master can be replaced in this mode.

Download and Upload:

Enables the IO-Link parameter data download and upload function.

An upload is performed when an IO-Link device is connected and the 
master does not have any valid data. This is the case if "Disabled and 
Cleared" mode was configured previously and/or in case of "Disabled" 
in as-delivered condition. The parameter data read are permanently 
stored on the master.

If parameter data are changed on the device during runtime, the 
device data stored on the master can be overwritten using the 
ParamDownloadStore (Index 0x0002, Subindex 0x00, Value 0x05) 
command. This command sets the DS_UPLOAD_REQ flag on the 
device, and thus executes an upload.

For each new connection to an IO-Link device, the master compares 
the stored parameter data with the device data. If the function is not 
locked on the device ("Parameter storage" locked), the master 
downloads the stored data to the device in case of differences.

The IO-Link device can be replaced in this mode.

Action

IO-Link master state

IO-Link device state

Upload

Invalid Data (Cleared before)

Upload Flag active (Valid Data)

Upload

Invalid Data (Cleared before)

Upload Flag not active & Valid Data

Upload

Valid Data

Upload Flag active & Valid Data

Download

Valid Data

Upload Flag not active (Data Equal)

Содержание 934 840 001










































































































Отзывы:

Нет отзывов