Belar FMHD-1 Скачать руководство пользователя | Manualshive

Страница: 22 / 58

background image

FMHD-1 Operator’s Manual

Page 14

FMHD-1

3.5, 4.0, 4.5,

or

5.0

seconds. An “

Infinite

” hold-time is also possible. These are all set from

the Unit Settings Popup Menu.

In "

Past

” time mode (with “

Infinite: OFF

”), the

FMHD-1

samples the appropriate signal stream

for the time interval set by the “

Hold Time

” parameter. The Peak indication is the highest reading taken

during that interval. The Average indication is computed from the peak values collected during that same
hold-time; the Minimum is the lowest modulation peak occurring during the hold-time.

In “

Real

” time mode (“

Infinite: OFF

”), the modulation or level stream itself controls the starting

points of the measurement time windows. In “

Rea

l” time, no matter the

Hold Time

setting, the

occurrence of a peak which exceeds the peak presently displayed causes the new, higher peak to be
immediately displayed. At the same moment, the Average modulation occurring since the previous update
is computed and displayed, along with the Minimum peak value for the interval. The window timer is
reset to zero, and the accumulation of modulation data is restarted. It continues until either an even higher
Peak reading occurs, or until the time passing since this most recent reset reaches the window length set
by the

Hold Time

parameter.

When the time parameter “

Infinite

” is “

ON

,” the highest Peak and Average readings are collected and

held until they are replaced by successively higher ones. Correspondingly, Minimum readings are
collected until replaced by successively lower ones.

4.4

FMHD-1 Bargraph Displays

Two of the

FMHD-1

display screens have three-color bar graphs to indicate dynamically changing signal

levels. These tri-color bar graphs provide simultaneous indications of the Peak modulation or program
level (in red), the Average level (in yellow) and the Minimum level (in green). Characteristics of the
indications are controlled by settings in the Unit Settings Pop-up Menu. (See Section 6.3.1 on page 25.)

For all settings, the Peak indication is read at the right edge of the red portion of the bar. Likewise, the
right edge of the yellow portion of the bar indicates the Average value, and the right edge of the green
portion of the bars indicates the Minimum value occurring during the metering time window. (The space
between the three indications is filled for ease in reading.)

The preceding section, “

FMHD-1

Modulation/Program-Level Readings”, explains how the data for the

bargraph readings is obtained.

Descriptions of the two bargraph screens follow below under Section 5, “The

FMHD-1

Display Screens”.

4.5

Spectrum Display

The user interface for, and the operation of the

FMHD-1

spectrum display are presented in Section 7,

“

FMHD-1

Frequency Spectrum Display and Functions”, beginning on page 29.

5

The FMHD-1 Display Screens

5.1

Main Tuning Screen

The

FMHD-1

Main Tuning Screen is an observation point for routine monitoring of FM IBOC

broadcasts. At the top center of the display is the carrier frequency to which the

FMHD-1

is tuned. The

«
...
20
21
22
23
24
...
»

Содержание FMHD-1



























































Отзывы:

Нет отзывов

Похожие инструкции для FMHD-1

Бренд: NEC Страницы: 14

SyncMaster C27A750X

Бренд: Samsung Страницы: 102

Бренд: Raymarine Страницы: 12

SyncMaster 753 DFX

Бренд: Samsung Страницы: 82

Viera TH-37PH10

Бренд: Panasonic Страницы: 53

GPSMAP 9000 Series

Бренд: Garmin Страницы: 28

Бренд: Alecto Страницы: 25

Cintiq Pro DTH-3220

Бренд: Wacom Страницы: 78

Бренд: Samtron Страницы: 115

Бренд: XP-PEN Страницы: 12

UltraView AP-10AV Series

Бренд: I-Tech Страницы: 28

VG910B - 19" LCD Monitor

Бренд: ViewSonic Страницы: 21

Бренд: ViewSonic Страницы: 25

Бренд: Unicont SPb Страницы: 16

Бренд: ViewSonic Страницы: 19

ecomatDisplay CR1152

Бренд: IFM Страницы: 21

Бренд: Garz & Fricke Страницы: 32

Poly Medialign 65

Бренд: Plantronics Страницы: 157

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды