Belar FMHD-1 Скачать руководство пользователя | Manualshive

Страница: 19 / 58

background image

FMHD-1 Operator’s Manual

BELAR ELECTRONICS LABORATORY, INC.

Page 11

The RS-232 D-connector pin numbers are:

Description

Pin#

Type

CTX

1

Input

RX

2

Input

TX

3

Output

RTS

4

Output

GND

5

Ground

Pins 6–9 are not used.

3.6

FMHD-1 System De-Emphasis

All audio outputs of the

FMHD-1

are de-emphasized, i.e. the audio has the same frequency response at

the output as the program signals driving the IBOC encoder feeding the transmitter. The analog channel
outputs conform to the US standard 75-microseconds. De-emphasis is defined on page 34 in the

“Definitions”

section.

4

Operation

4.1

The User Interface

The

FMHD-1

is controlled via a single large rotary encoder knob, which incorporates a momentary push

switch. A 640 X 240-pixel LCD color display is the primary front-panel readout for the monitor. User-
controlled settings of the unit are assigned to the multiple screens and “popup” menus which may be
selected for display.

Operation via the front-panel is described below. The unit may also be operated remotely via

Belar

’s

WizWin©

software running on a remote PC. The PC may be connected to the

FMHD-1

via either the

rear-panel RS-232 port or an Ethernet-type LAN or internet connection. The

WizWin

software presents a

virtual image of the

FMHD-1

front-panel display on the PC screen. Therefore, remote operation on a PC

mimics operation from the front-panel and will not be discussed. (To download the latest version of the

WizWin

software, go to www.belar.com. Instructions for downloading appear there, as well as in

Sections 9.3 and 9.4 of this manual.)

4.2

Front-Panel Operation

4.2.1

The Rotary Encoder

The rotary encoder, much like a computer mouse, provides the means to navigate the FMHD-1 display
screens, to select parameters, and to change settings.

For a listing of the top-level screens, see Table 1,

“

FMHD-1

Display Screens”, on page 40. For the popup menus and their access points, see Table 2,

“

FMHD-1

Popup Menu Map”, on page 41.

4.2.2

Navigation

Rotating the (rotary) encoder knob navigates through the display screens in both directions, in a

wrap-around fashion. The presence of the

▲

▼

▲

▼

symbol, for “Exit Screen”, in the upper-right corner of any

screen indicates that the cursor is active in the screen presently in the display and that the cursor is

«
...
17
18
19
20
21
...
»

Содержание FMHD-1



























































Отзывы:

Нет отзывов

Похожие инструкции для FMHD-1

Mondopad INF8521

Бренд: InFocus Страницы: 45

Бренд: Dante Страницы: 60

Бренд: Smart Technologies Страницы: 98

Babyviewer 4100

Бренд: Topcom Страницы: 2

Large Matrix Galaxy GT6X Series

Бренд: Daktronics Страницы: 33

FP767 - 17" LCD Monitor

Бренд: BenQ Страницы: 47

Бренд: ViewSonic Страницы: 2

Бренд: EverFocus Страницы: 1

Бренд: Hisense Страницы: 2

Бренд: Balmar Страницы: 19

Бренд: Autoleader Страницы: 16

Бренд: Hisense Страницы: 33

ELITE GRAPHIC WALL EGW-66

Бренд: Abex Exhibits Страницы: 3

Бренд: LEGRAND Страницы: 9

Бренд: ViewSonic Страницы: 20

Бренд: Fujitsu Страницы: 35

Бренд: Fujitsu Страницы: 10

Бренд: Fujitsu Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды