Belanger insta-KLEEN Скачать руководство пользователя

Страница: 37 / 88

insta-KLEEN

™ MANUAL

1MANUL334

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Installation

Photo Eye Tunnel Placement

There are two types of Photo Eyes available. The original

Floor Mounted

and the optional

Wall

mounted

. Both styles are wired the same, but they have different variables to consider for

positioning.

DO NOT secure Photo Eyes into place until you have read this entire manual.

The following shows basic placement of both styles. The remaining pages will show mostly
Floor mounted since both styles are similarly positioned.

Floor Mounted

Once mounted, the Photo Eyes are to be pivoted to
point directly at each other

Emitter

Receiver

Floor Mounted, View from Entrance

Floor Mounted, Overhead View

Photo Eyes are typically mounted with an approximate offset of 36

”

(91.4 cm).

They can be mounted with a minimum offset of

6”

(15.2 cm) up to a maximum

offset of 120

”

(3.0 m).

Receiver

Emitter

”

(91.4 cm)

Содержание insta-KLEEN

























































































Результаты поиска

Содержание insta-KLEEN

Отзывы:

Похожие инструкции для insta-KLEEN

Бренды по названию

Популярные бренды

Belanger insta-KLEEN, Руководство пользователя

Результаты поиска

Содержание insta-KLEEN

Отзывы:

Похожие инструкции для insta-KLEEN

Бренды по названию

Популярные бренды