Belanger insta-KLEEN Скачать руководство пользователя

Страница: 19 / 88

insta-KLEEN

™ MANUAL

1MANUL334

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Introduction

Before You Get Started

Tools needed for installation:

Chalk line

Extension cord

Level

Hex wrench set

Wrench set

Square

Socket set

Ladder

Impact wrench

Tape measure (50 foot / 15 meter or greater)

Miscellaneous hand tools

Tin snips

Pry bar

Hammer drill with

1/2”

(12.7mm)

and 5/8”

(15.8mm) bit

Forklift (5000 lb.) / (2200kg)

Safety glasses

Work gloves

Field Purchased Supplies Needed for Installation:

3HP / 2.25kW air compressor

What to Know Before You Get Started

The insta-KLEEN

™ is a flexible system. It can

be  ordered  in  many  configurations  and  with
many options. Please  check your  order against
your shipper and the equipment received. Verify
that  you  have  received  all  the  equipment
ordered.

NOTE: If any items listed below are not included in your shipment, contact your supplier.

NOTE: The insta-KLEEN

™

Wash System is completely electrically driven.

Содержание insta-KLEEN

























































































Результаты поиска

Содержание insta-KLEEN

Отзывы:

Похожие инструкции для insta-KLEEN

Бренды по названию

Популярные бренды

Belanger insta-KLEEN, Руководство пользователя

Результаты поиска

Содержание insta-KLEEN

Отзывы:

Похожие инструкции для insta-KLEEN

Бренды по названию

Популярные бренды