background image

Page  5

Turn on and testing

30  cm
m a x

1-4  m

30  cm
m a x

1-4  m

N O !

N O !

Detector  Gas
METHANE

YES

Detector  Gas
LPG

Installation measures and positioning

The  position  of  the  detector  is  a  crucial  factor  for  its  correct  functioning  during  gas  detection.
In  order  to  obtain  the  maximum  results  from  a  device  and  minimize  the  probability  of  false  alarms,
it  is  recommended  to  follow  this  scheme  and  keep  in  mind  the  following  general  regulations.

The  detector  must  be  located  at  different  heights,  according  to  the  type  of  gas.  These  heights  are:

-  30  cm  from  the  lowest  point  of  the  floor  in  order  to  detect

heavy gases, LPG, etc.

-  30  cm  from  the  highest  point  of  the  ceiling  in  order  to  detect

light gases, Methane

- The detector should not be placed near the appliances to be controlled (boilers, burners, industrial
kitchens,  etc.)  but  on  the  opposite  wall.
- The detector should not be affected by smoke, vapour, etc. as they could distort its measurement.
It  should  be  located  away  from  sources  of  heat,  ventilators  or  fans.

It must not be installed, on a wall in plasterworch.
It must be installed only on walls in masonry

Once the device has been turned on, the MAINS LED will start blinking for about 60 seconds, after
which it will remain ON. Now the GS920 is ready for detection of explosive gas.

After 24 hours from installation begin the self-learning antiseismic period (from this time the detector
MUST NOT be moved from the installation position for any reason).

After  10  days,  the  self-learning  period  is  finished  and  the  device  is  capable  to  detect  seismic
movement.

Testing

Press  the  button  near  the  detection  capsule  to  simulate  the  presence  of  gas.
The  ALARM  LED  lights  up,  and  the  relay  shifts  its  functioning  mode  after  5  seconds.  After  the
alarm,  the LED  will turn  off,  the buzzer  will stop,  and the  connected  appliances will  be turned  off.
To complete the general test, issue gas from a pre-calibrated aerosol within 20% of  L.E.L. Testing
using a common cigarette lighter could damage the sensor. This test should be carried out at least
once  a  year.

Содержание GS920













Отзывы: