background image

Page  3

Year  2010

1

2

3

5

6

8

4

1  2

ON

7

9

1 2 3 4 5 6 7 8

  GS920
Methane

10

    Replace
    2014

S.N.  12472
Year  2010

Components and commands

1)  MAINS  connected  indication  LED.  When  the  green  LED  is  blinking,  the  GS920  performs  a  test  of
the  sensor’s  efficiency  status,  and  gets  it  to  the  functioning  temperature.  This  phase  lasts  about  60
seconds.  At  the  end,  the  LED  stops  blinking  and  the  green  light  remains  ON.
During the test period, the GS920 does not detect the gas.
2)
  FAULT  and  functional  life  wear  indication  LED.
If  this  LED  turns  on,  it  means  that  the  gas  detection  catalytic  sensor  is  not  working  efficiently  and
must  be  replaced  by  an  authorized  technician.
The sensor duration is  guaranteed for 6  years (in clean air). After six years, the yellow LED will start
a  quick  blinking.  You  will  hear  a  short  beep  every  hour.
3) ALARM  indication LED.  This LED  turns on  when room  gas  concentration  exceeds the  danger level,
at 10% of  L.E.L.

4)  Micro  switches:
Switch 1:  Positioning the switch to ON – Intrinsically safe operation – the relay is excited at the
end  of  the  latency  time  and  switches  on  each  alarm.
Positioning  the  switch  to  OFF  –  Normal  operation  –  the  relay  switches  on  each  alarm.
Switch 2: Positioning the switch to ON, the relay is set to impulse functioning. Each pulse lasts about
30  seconds.
Positioning  the  switch  to  OFF,  the  relay  goes  in  continuous  functioning  mode,  until  the  gas  threshold
drops  under  the  danger  level.

5)  Catalytic  sensor  for  Methane  or  LPG  explosive  gas  detection.
6)  TEST  button.  This  button  is  used  to  simulate  a  gas  leak,  after  installation.
7)  RESET  button.  This  button  is  used  to  stop  the  alarm,  when  triggered  by  an  EARTHQUAKE.
8)  Identification  label,  registration  number  and  manufacturing  year,  located  under  the  ABS  small
dome.
9)  TEST  POINT  for  testing.  It  is  used  in  the  laboratory  or  by  a  qualified  technician.

10)

Label  of  the  gas  sensor  expiration  date.

This label should be applied by the technician during installation, keeping in mind that the detector
should be overhauled after 5  years.

Содержание GS920













Отзывы: