background image

13)  RESET

Down

UP

Left

Right

ENTER

SN AD012G           16/Ago/19
Methane                 10:10
Sensor 29      Exp.

 020% 

100%

15,0%  LEL

 

ppm

Home screen

In  the  normal  operating  state  of  the  control  unit,  the  display  shows  the  following  information:
a)  Serial  number
b)  Current  date  and  time
c)  Type  of  gas  of  the  sensor  is  reading
d)  Current  sensor  reading  “address”  from  n°  1  to  n°  32.
If  in  the  reserved  addresses  (31-32)  is  connected  to  a  CARD-TX4R    it  will  be  read  Card-TX4R  31-32).
The  operating  range  of  each  sensor,  20%  or  the  100%  of  LEL,  this  happens  directly  from  the  sensors  DIP2
N.B.  The  change  of  each  sensor  is  carried  out  every  8  seconds.
1)  To  accelerate  the  display  of  the  sensors,  press  the  buttons  right  and  left.
2)
  To  lock  or  unlock  the  sequence  of  sensors,  and  analyse  the  functioning  of  a  specific  sensor,  press  “ENTER”.
the  display  shows  a  key  symbol.
e)  Display  of the  percentage  of  L.E.L.  or ppm  detected  by  the  sensor, and  the  graphic  of  the  gas  quantity  that
the  sensor  is  detecting.

Setting the control unit

To  access  the  BXI32  setting  program  you  should  press  the
“ENTER”  button  for  4  seconds.

The  program  provides  to  enter  a  password
La    “Password”  di  fabbrica    è    1-2-3-4.
The  Password  can  be  changed  by  accessing  to  "Advanced
Functions"
  program  under  "General  Function
s".

Move  with  the  left  button  above  the  required  number,  and
press  "ENTER",  every  asterisk  will  turn  on  every  number,
until  all  four  asterisks  are  switched  on.

If  the  PassWord  is  correct  it  reads  "Accepted  Password"
If you enter the  wrong  code you read "Wrong Password",
repeat  the  entry.
N-B.  after  three  wrongs  attempts  the  control  panel  comes
out  of  the  insertion

       enter password
        0 1 2 3 4 5 6 7 8 9
        * * * *
         password  accepted

Selecting  Functions

Select  the  desired  function  with  the  "UP"  and  "DOWN"
buttons
When  selected,  press  "ENTER"

Press  "End"  to  come  out  menu

Time           setting
Inputs       setting
General        functions
end

Page  5

Date  and  time  setting

             Date
hour
     26/Set/2017           15:10

To  set  the  date  and  time  proceed  as  follows:
1) Navigate with  the right and left buttons  above  the  day,
month,  and  year,  hour,  and  minute.
2)  Select  with  the  ENTER  button  to  find  the  day,
month  or  year,  hour,  minute,  desired
N.B.   In  case  of  lack  electric,  the  control  unit  does  not  lose
the  stored  data.
In  case  the  internal  battery  is  exhausted,  it  will  appear  at
startup  or  reset  of BXI32 the  written: “Err. bat. orologio

END:  to  exit  the  program,  select:

    “the  return  arrow”.

Содержание BXI32

























Отзывы: