BeiJer BFI-P2 Series, Инструкция по установке и эксплуатации

Страница: 27 / 84

Version 3.04
| Beijer BFI-P2 User Guide |
27 www.beijerelectronics.com
4.11. IP66 Switched Version Integrated Control Switch and Potentiometer Wiring
Beijer BFI-P2 is optionally available with an integrated mains switch-disconnector and front mounted control switch and potentiometer.
This allows the drive to be operated directly from the front control panel, whilst also providing for options such as Hand / Auto or
Local / Remote Control etc.
The integrated switch in IP66 Outdoor models operates in parallel with drive terminal 2 (T2) and terminal 3 (T3) as digital input 1 and
digital input 2. By default, the integrated switch is enabled.
Integrated Control Switch and Potentiometer Wiring
Switch Left Switch Centre Switch Right
DI1 DI2 DI1 DI2 DI1 DI2
1 1 0 0 1 0 Lc-Off
0 0 0 0 0 0 Lc-On
0 1 0 0 1 0 Altern
+2
4V DC DI 1 DI 2 DI 3
+1
0V DC AI 1
0V / C
OM
1 2 3 4 5 6 7
0/4-20 mA
4.11.1. Disabling built-in switches
If required, the built-in control switch may be disabled using the following method:
1) Ensure the drive is stopped (Display shows “Stop”).
2) Enable Advanced Parameter Access by setting the correct value in P1-14 (default : 201).
3) Scroll down to parameter P0-01 (Display shows P0-01).
4) Press and hold “STOP” button for >1s, drive will show:
IP66 Switch Setup
2: Pos >>DI1, Pos<<DI2
1: Switch disabled
0: Pos >>DI1, Pos <<DI1&2
5) Use “UP” or “DOWN” key to select the option:
0: Pos >>DI1, Pos <<DI1&2
means integrated switches are enabled.
1: Switch disabled
means the switches are locked/disabled.
2: Pos >>DI1, Pos<<DI2
means that Revers direction is disabled via built-in switch (can be unlocked via external enable signal
connected to DI1 – terminal 2).
6) Press the “STOP” button again to exit.
4.12. Motor Thermal Overload Protection
4.12.1. Internal Thermal Overload Protection
Beijer BFI-P2 has internal motor overload protection (current limit) set at 150% of FLC. This level may be adjusted using P4-07.
The drive has an in-built motor thermal overload function; this is in the form of an “I.t-trP” trip after delivering >100% of the value set in
P1-08 for a sustained period of time (e.g. 150% for 60 seconds).
4.12.2. Motor Thermistor Connection
Where a motor thermistor is to be used, it should be connected as follows:
Motor Thermistor Connection Additional Information
+2
4V DC DI 1 DI 2 DI 3
+1
0V DC AI 1
0V / C
OM
AO
1
0V / C
OM
AI 2
AO
2
ST
O
+
ST
O
-
 Compatible Thermistor: PTC Type, 2.5kΩ trip level.
 Use a setting of P1-13 that has DI5/AI2 function as E-TRIP
“External Trip”, e.g. P1-13 = 6. Refer to section 7.2. Digital
Input Configuration Parameter P1-13 on page 42 for
further details.
 Enable the Motor PTC Thermistor Input function in parameter
P2-33.
1 2 3 4 5 6 7 8 9
10
11 12 13
4
Elec
trical Installation