Beha-Amprobe GT-600 Скачать руководство пользователя страница 53

Страница: 53 / 76

GT-600/GT-800 Instruction Manual

Memorizing Example

In order to save measurement result, follow the next instructions:

1) Carry out the measurement, result is displayed.
2) Press the “SAVE” function key (5), blank level “APP” (appliance) will be

marked.

Barcode reader is not used:
3) Press the “NEW” menu key first, then enter new appliance name by

using the “

▼

”, “

▲

” and “



“ menu keys. Confirm entered name by

pressing the “



” menu key, cursor will move to “CLI” (client) level.

4) Confirm offered “CLI” name by pressing the “



” menu key or modify it

by pressing the “MOD” menu key first and then by using the “

▼

”, “

▲

”

and “



“ menu keys. Confirm entered name by pressing the “



” menu

key, cursor will move to “SIT” (site) level.

Note! Entry of the client is not obligatory as it is considered just as an
appendix to the Appliance.

5) Confirm offered “SIT” name by pressing the “



” menu key or modify it

by pressing the “MOD” menu key first and then by using the “

▼

”, “

▲

”

and “



“ menu keys. Confirm entered name by pressing the “



” menu

key, cursor will move to “LOC” (location) level.

Note! Entry of the site is not obligatory as it is considered just as an
appendix to the Appliance.

6) Confirm offered “LOC” name by pressing the “



” menu key or modify

it by pressing the “MOD” menu key first and then by using the “

▼

”,

“

▲

” and “



“ menu keys. Confirm entered name by pressing the “



”

menu key, cursor will move to blank “DES” (description) level.

Note! Entry of the location is not obligatory as it is considered just as an
appendix to the Appliance.

7) Enter new description by pressing the “MOD” menu key first and then

by using the “

▼

”, “

▲

” and “



” menu keys. Confirm the entry by

pressing the “



” menu key, cursor will move to APP (appliance) level

again.

Note! Entry of description is not obligatory as it is considered just as an
appendix to the Appliance.

8) Press the “SAVE” function key again to store the measurement result,

memorizing is confirmed with “SAVED” visual information and double
sound signal.

Barcode reader is used:
3) Scan the appliance code (no need to press the “NEW” menu key first),

cursor will move to “DES” (description) level.

4) Scan the description (no need to press the “MOD” menu key first),

cursor will move to “APP” (appliance) again.

Note!
If CLI (client), SIT (site) and LOC (location) are needed to be scanned too,
then select wished line manually first by using the “



” menu key and scan

appropriate information.

Содержание GT-600













































































Результаты поиска

Содержание GT-600

Отзывы:

Похожие инструкции для GT-600

Бренды по названию

Популярные бренды

Beha-Amprobe GT-600, Руководство пользователя

Результаты поиска

Содержание GT-600

Отзывы:

Похожие инструкции для GT-600

Бренды по названию

Популярные бренды