background image

Transport and storage

Version: 1.0

───

 

45

eXtended Transport System

Avoid damage to the components and loss of guarantee

Observe the conditions and the following chapters on transport and
storage.

Disregarding the conditions can lead to damage to the components
and the voiding of the guarantee.

6.1

Conditions

Take care during transport and storage that the individual XTS Hy-
gienic  components  are  not  damaged.  Observe  the  following  chap-
ters and maintain the following conditions:

• Climate category: 2K3 according to EN 60721

• Temperature: -25 °C to +85 °C, maximum fluctuation 20 K/hour

• Use of the vendor's original packaging

6.2

Long-term storage

Perform recurring inspections

Check every six months that the XTS Hygienic is in good condition.

Damage  to  the  XTS  Hygienic  or  failure  to  carry  out  maintenance
work can shorten the service lives of the installed components and
parts.

Prevent the formation of condensation

Keep  the  ambient  temperature  constant.  Avoid  solar  radiation  and
high humidity.

Condensation water can lead to damage during subsequent opera-
tion or to rust formation.

You have the option to store XTS components over a short or long
period. For storage we always recommend the original packaging.

Содержание ATH2000-0250





































































































Отзывы: