Beam IsatDock DRIVE Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 32

Beam IsatDock DRIVE Скачать руководство пользователя страница 15

IsatDock DRIVE - Installation & User Manual

15

• Verify that low resistance connections are

present between the battery negative
terminal, the vehicle chassis, and the
engine block. All wire connections should
be clean and tight.

• For vehicle installation, install provided

fuses into the +BATT and ignition sense
(accessory) wires.

WARNING

Do not connect the IsatDock interface
power cable to power the unit until the full
installation is completed.

Installation Procedure

Installing the IsatDock DRIVE Cradle

Install the components in the following order.
More detailed instructions can be found in the
sections following.
1.

Mount the IsatDock DRIVE cradle

2.

Install the external BEAM antenna

3.

Connect the speaker and microphone to
the IsatDOCK DRIVE cradle

4.

Connect the privacy handset
(ordered as extra option)

5.

Connect the DC power cable

6.

Connecting Horn / Mute wires

7.

Install the external alert button (optional)

8.

Configure Tracking / Alert (optional)

When selecting a location for the IsatDock
cradle, consider these guidelines:
•

Ensure that each mounting surface is
strong enough to support the cradle.

•

Allow enough room so that you can easily
insert the IsatPhone Pro handset in and
out from the cradle.

•

Ensure that the IsatDock is within cable
distance of power and antenna connections

•

Position the handset and cables so that it
does not interfere with vehicle operation or

with driver or passenger seating or leg space.

•

Ensure sufficient room is allowed for the
antenna and interface cables to be routed
from the rear of the IsatDock cradle.

1) Mount the IsatDock DRIVE cradle

The IsatDock DRIVE is supplied with a universal RAM®
mount bracket that enables mounting to any flat
surface (vertical or horizontal) within a vehicle, or
other required location.
1.

Attach one pivot base to the rear of the
IsatDock DRIVE using the M4 screws supplied.

2.

Secure the second pivot base to the
location you have selected for mounting
the IsatDock DRIVE.

3.

Use the interconnecting step of the
RAM® mount to secure the IsatDock
DRIVE to the pivot base and tighten into
the desired location firmly using the
wing nut on the stem.

[1] [2] [3]

«
...
13
14
15
16
17
...
»

Содержание IsatDock DRIVE

































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды