Baxi 741 Скачать руководство пользователя | Manualshive

Страница: 5 / 34

background image

*

When converted using kit 0595211.

The appliance data label is located on a plate at the base of the fire. This can be seen by
removing the lower front casting.

3. GENERAL INSTALLATION REQUIREMENTS

3.1

The installation must be in accordance with these instructions.

For the user’s protection, in the United Kingdom it is the law that all gas appliances are
installed by competent persons in accordance with the current edition of the Gas Safety
(Installation and Use) Regulations. Failure to install the appliance correctly could lead
to prosecution. The Council for the Registration of Gas Installers (CORGI) requires its
members to work to recognised standards.
In the United Kingdom the installation must also be in accordance with:
All the relevant parts of local regulations.
All relevant codes of practice.
The relevant parts of the current editions of the following British Standards:-
BS 715

BS 1251

BS 1289 Part 1

BS 1289 Part 2

BS EN 1806

BS 4543 Part 2

BS 5440 Part 1

BS 5440 Part 2

BS 5871 Part 2

BS 6461 Part 1

BS 6891

BS 8303

In England and Wales, the current edition of the Building Regulations issued by the
Department of the Environment and the Welsh Office

Page 5

INSTALLER GUIDE

Gas

Natural (G20)

Propane (G31) *

Inlet Pressure

20mbar

37mbar

Input - Max. (Gross)

6.85kW (23,400 Btu/h)

6.7kW (22,860 Btu/h)

Input - Min. (Gross)

2.3kW (7,850 Btu/h)

4.0kW (12,970 Btu/h)

Inlet Test Pressure (Cold)

20.0 ± 1.0mbar (8.0 ± 0.4in

w.g.)

37.0 ± 1.0 mbar (14.85 ±

0.4in w.g.)

Gas Connection

8mm pipe

8mm pipe

Burner Injector

Stereomatic Cat 82 - 074

Stereomatic Size 132

Pilot & Atmosphere Sensing

Device

Copreci Ref. O.D.S

21500/166

Copreci Ref. O.D.S

21500/166 Fitted with RBM

180 -02 injector

Ignition

Integral piezo (Mounted on

gas valve)

Integral piezo (Mounted on

gas valve)

Aeration

See section 17.1

Non-adjustable

«
...
3
4
5
6
7
...
»

Содержание 741



































Отзывы:

Нет отзывов

Похожие инструкции для 741

Бренд: Harrie Leenders Страницы: 26

Бренд: Rinnai Страницы: 21

Бренд: Quadra-Fire Страницы: 36

Бренд: Napoleon Страницы: 17

Бренд: FireplaceXtrordinair Страницы: 24

Бренд: Ravelli Страницы: 9

88317/23MM5661-Z402

Бренд: Style selections Страницы: 21

Бренд: FBR Страницы: 30

Бренд: kozy heat Страницы: 51

Comfort Glow CGFB32CB

Бренд: Desa Страницы: 36

Бренд: RUSTA Страницы: 26

Бренд: HAMPTON BAY Страницы: 32

Бренд: Wamsler Страницы: 88

Colorado Mesh Chimenea XL

Бренд: La Hacienda Страницы: 4

Бренд: IHP Страницы: 2

Бренд: Heat Surge Страницы: 36

Бренд: CVO Fire Страницы: 44

Бренд: Faber Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды