Baxall HYPER-D Series Скачать руководство пользователя страница 10

Страница: 10 / 12

Hyper-D Series

Installation Instructions

SYNC

This menu is used to select the way the camera maintains frame synchronisation.

INTERNAL

For internal synchronisation.

PHASE 1, PHASE 2

PHASE 3

When synchronising multiple Hyper-D cameras in a three-phase installation. Each setting

has a 120

offset.

LINELOCK 0-360

For adjusting vertical phase when synchronised to an AC supply.

Note:

Line-lock synchronisation may cause some issues with on screen displays. In these

circumstances the camera should be set to internal synchronisation.

MOUNTING

Mounting points (12, figure 1) are provided on the top and bottom of the camera and are

used to mount the camera on a bracket or tripod. Only use standard, photographic 1/4-20

UNC mounting bolts.

MODE

NORMAL

AGC

MED

WHITE BALANCE RANGE

PRO

FLUORESCENT

OFF

> SYNC

SAVE AND EXIT

Содержание HYPER-D Series













Результаты поиска

Содержание HYPER-D Series

Отзывы:

Похожие инструкции для HYPER-D Series

Бренды по названию

Популярные бренды

Baxall HYPER-D Series, Руководство по установке

Результаты поиска

Содержание HYPER-D Series

Отзывы:

Похожие инструкции для HYPER-D Series

Бренды по названию

Популярные бренды