Baumalight TRL620Y Скачать руководство пользователя страница 7

Страница: 7 / 48

1.5 Operator Orientation

Front

Right Side

Rear

Left Side

1.6 OEM Engine

Detailed engine information and warranty can be

found in the Yanmar engine manual provided with

the skidsteer.
The basic engine warranty is as follows:
• Engine is covered for 2 years from date of

original purchase, or 2000 hours, whichever

occurs first. For TNV Series Industrial Engines

only, an extended limited warranty of 3 years

or 3000 engine operating hours, whichever

occurs first, is provided for these specific

parts only: the cylinder block, cylinder head,

crankshaft forging, connecting rods, flywheel,

flywheel housing, camshaft, timing gear, and

gear case.

•

Radiator, engine isolation mounts, muffler and

drive couplings are not part of the Yanmar

warranty, but are covered by their manufacturer

for 1 year. Any non Yanmar supplied parts are

not part of the Yanmar warranty and would be

covered based on that particular supplier’s

warranty policies.

• While the engine is under warranty, all claims

must be approved by an authorized Yanmar

industrial engine dealer or distributor before

any work is started. Warranty claims without

proper authorization will be denied.

Yanmar highly recommends registering the retail

purchaser’s information through the website

http://www.yanmar.co.jp as soon as possible.
If it is not possible to access the website, please

contact the nearest authorized Yanmar industrial

engine dealer or distributor.

Содержание TRL620Y

















































Результаты поиска

Содержание TRL620Y

Отзывы:

Бренды по названию

Популярные бренды

Baumalight TRL620Y, Руководство оператора

Результаты поиска

Содержание TRL620Y

Отзывы:

Бренды по названию

Популярные бренды