Baumalight TRL620Y Скачать руководство пользователя страница 19

Страница: 19 / 48

Check Engine Oil Level

Skidsteer must be parked on a level surface,

lift arms fully lowered, engine stopped and key

removed.

Remove second engine side panel from the

front on left side of skidsteer.

Clean around oil dipstick (A).

Pull out dipstick (A) and wipe metal end clean.

Slide dipstick fully into dipstick tube.

Pull dipstick out and look at metal end.

If oil level is low, loosen knobs (B) and tilt

hydraulic cooler up. Engage pin to hold cooler

in up position.

Clean around oil filler cap and remove cap (C).

The OEM engine manufacturer specifies the oil

be API service categories CD, CF, CF-4, CI-4 or

higher. Change the type of engine oil according to

the ambient temperature.

32° F

0° C

50° F

10° C

68° F

20° C

86° F

30° C

104° F

40° C

-22° F

-30° C

-4° F

-20° C

14° F

-10° C

SAE

10W-30

SAE

5W-30

SAE

15W-40

SAE 30

SAE 20

When using oil of different brands from the

previous one, be sure to drain all the previous

oil before adding the new engine oil. Refer to the

OEM engine manual for detailed oil information

and recommendations.

Содержание TRL620Y

















































Результаты поиска

Содержание TRL620Y

Отзывы:

Похожие инструкции для TRL620Y

Бренды по названию

Популярные бренды

Baumalight TRL620Y, Руководство оператора

Результаты поиска

Содержание TRL620Y

Отзывы:

Похожие инструкции для TRL620Y

Бренды по названию

Популярные бренды