manualshive.com logo in svg

Baumalight TRL620Y, Руководство оператора

Поделиться
Скачать
Baumalight TRL620Y Скачать руководство пользователя страница 24

4.5 Start And Stop Engine

Refer to OEM engine manual for detailed 

instructions.

^

 

WARNING

Carbon monoxide hazard.

Always start and operate the engine in a 

well-ventilated area.

If in an enclosed area, vent the exhaust 

to the outside.

For more information go to www.

P65Warnings.ca.gov.

Start Engine - Above 40° F (4° C)

1. 

Verify all controls are in neutral.

2. 

Move throttle lever to low-medium position.

3. 

Turn ignition switch to start position until engine 

starts. Release ignition switch when engine 

starts.

4. 

Allow engine to run for 5 minutes to warm up.

5. 

Move the throttle lever to desired setting.

Start Engine - Below 40° F (4° C)

1. 

Verify all controls are in neutral.

2. 

Move throttle lever to medium position.

Note:

 Attempting to start a cold engine while 

standing on operators platform will draw more 

battery power since the drive and boom functions 

are enabled. 

3. 

While standing off of operators platform, turn 

ignition switch to run position for approximately 

8 seconds to activate pre-heat.

4. 

When  pre-heat  lamp  goes  off,  turn  ignition  

switch to off.

5. 

Turn and hold ignition switch in the start position 

to begin cranking engine over. Never hold 

ignition switch in the start position for longer 

than 8-10 seconds. Engine should begin to run 

after about 3 seconds.

6. 

Release ignition when engine begins to run. If 

engine stalls, turn and hold ignition switch in 

the start position again to re-start. 

NOTICE

Prevent engine damage.

Do not turn ignition switch in the start 

position while engine is running or 

sputtering during a cold startup.

If engine stalls a few times after releasing 

ignition switch, it may help to keep ignition 

switch in the start position a few seconds longer 

than normal to help engine along. Release 

ignition switch when engine starts.

7. 

Allow engine to run for 5 minutes to warm up.

8. 

Move the throttle lever to desired setting.

Stop Engine

1. 

Lower lift arms to ground.

2. 

Move controls to neutral position.

3. 

Engage park brake.

4. 

Run engine at low idle for five minutes.

5. 

Turn ignition switch to stop.

6. 

Remove key.

20

Содержание TRL620Y

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды