Baumalight TRL620Y Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 48

background image

Drive Joystick

Push joystick forward (A) to move skidsteer

forward.

Pull joystick rearward (C) to move skidsteer

rearward.

For gradual turns, push joystick forward or pull

rearward, then move left or right. Skidsteer will

slowly turn left or right.

For tight turns, move joystick from center position

to right (B) or left (D). Tracks will counter rotate

and turn skidsteer in a tight circle.

The farther you move the joystick in any direction,

the faster the skidsteer will move in that direction.

Release joystick or move to the center neutral

position to stop movement.

A

B

C

D

A

B

D E

F

G

H

I

J

K

C

A.

Lights

B.

Hour Meter

C.

Engine Tachometer

D.

Lofa Engine Control Panel

E.

Hydraulic Fluid Pressure

F.

Ignition Switch

G.

Engine Throttle

H.

Boom Joystick

I.

Auxiliary Hydraulic Control

J.

Park Brake On/Off

K.

Drive Joystick

Engine Throttle

Move the control rearward to increase the engine

speed and forward to decrease speed.

Park Brake

Move switch forward to engage the park brake.

Move switch rearward to release park brake.

4.4 Machine Controls

18

«
...
20
21
22
23
24
...
»

Содержание TRL620Y

















































Отзывы:

Нет отзывов

Похожие инструкции для TRL620Y

Бренд: Xtreme Manufacturing Страницы: 74

POSI-TRACK SR-70

Бренд: ASV Страницы: 72

Бренд: Giant Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды