manualshive.com logo in svg

Baumalight TRL620Y, Руководство оператора

Поделиться
Скачать
Baumalight TRL620Y Скачать руководство пользователя страница 10

^

 

WARNING

Prevent explosion.

Skidsteer and/or attachment contacting 

a gas line can result in an explosion.

If you suspect a gas line has been damaged:

• 

Immediately shut off engine.

• 

Remove any ignition sources.

• 

Warn others that a gas line has been damaged 

and that they should leave the area.

• 

Leave the area as quickly as possible.

• 

Immediately call the local emergency phone 

number and the utility company.

• 

Do not return to area until given permission by 

emergency personnel and utility company.

Prepare For Emergencies

Be prepared in case of emergencies.

Keep a fire extinguisher and first aid kit close to 

the machine.

Keep emergency phone numbers in your phone.

Know your address so emergency services can 

locate you if an emergency arises.

Replace Safety Signs

Replace missing or damaged safety signs.

Safety  signs  are  identified  in  Section  3  of  this 

manual.

Replacement safety signs are available from your 

Baumalight dealer.

Do Not Allow Riders

NEVER lift or carry anyone on the skidsteer.
NEVER use skidsteer as a work platform.
NEVER allow passengers on the skidsteer.

Lower Operating Speed

Move at slow speeds on rough or uneven terrain.

Avoid Rollover

The equipment may rollover, resulting in death or 

serious injury. To help prevent rollover:
•  Travel at a slow speed.
•  Avoid sharp turns & sudden movement on 

slopes.

•  Carry attachments close to the ground.
•  Avoid holes, ditches and other obstructions 

which may cause equipment to rollover.

•  Use caution when operating on slopes and do 

not operate on excessively steep slopes.

•  Do not exceed load capacity of equipment.

6

Содержание TRL620Y

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды