Basler BE1-DFPR Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 135

background image

4-1

SECTION 4

INSTALLATION

GENERAL

When not shipped as part of a control or switchgear panel, BE1-DFPR relays are shipped in a sturdy carton
to prevent damage during transit. Immediately upon receipt, check the model and style number against the
requisition and packing list to see that they agree. Visually inspect for damage that may have occurred
during shipment. If there is evident damage, immediately file a claim with the carrier and contact a sales
representative at Basler Electric, Highland, Illinois.

In the event the unit is not to be installed immediately, store it in its original shipping carton in a moisture and
dust free environment. It is strongly recommended that an operational test (refer to Section 5) always be
performed prior to installation.

OPERATING PRECAUTIONS

Before installation or operation, observe the following precautions.

1.

Always be sure that external operating (monitored) conditions are stable before removing a BE1-DFPR
unit for inspection, testing, or servicing.

2.

BE1-DFPR relays are solid-state devices and have been type tested in accordance with the
requirements defined in the following paragraph, Dielectric Test. If a wiring insulation test is required
on your switchgear or panel assembly and this relay is to be tested, observe the information noted in
the following paragraph, Dielectric Test.

3.

Be sure that the BE1-DFPR chassis is hard wired to earth ground using the chassis ground (terminal
25) on the rear of the unit.

4.

When the unit is in service, the controls should be protected by the cover supplied. This limits access
to the control settings.

DIELECTRIC TEST

BE1-DFPR relays have been type tested in accordance with the requirements of IEC 255-5 and ANSI/IEEE
C37.90.1-1989. One-minute dielectric (high potential) tests of the assembled switchgear or control panel
wiring may be performed using up to 1500 Vac (45-65 Hz). Note that decoupling capacitors (0.01
microfarad) are employed from all terminals to surge ground. Accordingly, a leakage current of
approximately 5.6 milliamperes per terminal is to be expected when high potting at 1500 Vac, 60 hertz.

MOUNTING

BE1-DFPR relays are designed to be rack-mounted. Overall dimensions are shown in Figure 4-1. BE1-
DFPR relays may also be panel mounted. Use the cutout dimensions of Figure 4-2 as a guide. Relays may
be mounted at any convenient angle. Horizontal and vertical mount relays have the same overall and cutout
dimensions. Metric dimensions are shown in parentheses.

«
...
82
83
84
85
86
...
»

Содержание BE1-DFPR








































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-DFPR

Бренд: Eaton Compressor Страницы: 4

Бренд: Pilz Страницы: 27

SOLID STATE RELAYS SBG22445

Бренд: Omega Страницы: 2

White-Rodgers 829A-832

Бренд: Emerson Страницы: 4

Бренд: Phoenix Contact Страницы: 10

Бренд: Schweitzer Engineering Laboratories Страницы: 142

Бренд: Coster Страницы: 16

Бренд: Moeller Страницы: 4

ELMON rail 32-242

Бренд: ASO Страницы: 32

Бренд: ZIGBEE Страницы: 4

Бренд: Eaton Страницы: 1017

Бренд: ABB Страницы: 2

Бренд: ABB Страницы: 40

Бренд: IFM Страницы: 12

Бренд: GE Страницы: 23

Бренд: Woodward Страницы: 96

Бренд: Woodward Страницы: 59

Бренд: Schweitzer Engineering Laboratories Страницы: 232

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды