manualshive.com logo in svg

Basler BE1-DFPR, Инструкция по эксплуатации

Инструкция по эксплуатации Basler BE1-DFPR доступна для бесплатного скачивания на нашем сайте. Получите подробное руководство пользователя на русском языке, чтобы узнать все возможности этого продукта. Загрузите его сейчас с manualshive.com и начните использовать Basler BE1-DFPR эффективно и без проблем.

Поделиться
Скачать
background image

BE1-DFPR Testing

5-19

Settings menu.  This disables all other functions from tripping the relay so just the 50T function
can be checked.

Step 16. Connect a current source to any phase current input or the neutral current input.

Step 17. Close the breaker on the test set and wait for the RST LED to illuminate on the relay.

Step 18. Apply an appropriate amount of current to trip the relay and measure the time from when the

current is applied until the Trip 1 contacts close.  This timing should be within ±5% or 25 ms of the
time delay setting that is set in the Relay Settings screen (50TP TD for a phase timing and 50TN
TD for a neutral timing).

Step 19. Return to the Tripping Logic screen and return the Trip 1 settings to the desired values.  Press

ESC to save the settings, then press ESC again to return to the Review/Edit Settings menu.

27 Timings

Step 20. From the Review/Edit Settings Menu on the terminal, select 2, 5, 8, I, or L to enter the Tripping

Logic screen for the desired settings group.

Step 21. Enter N in all Trip 1 locations except 27/59.  Enter Y in the 27/59 location.  Press ESC to save

these settings, then press ESC again to return to the Review/Edit Settings menu.  This disables
all other functions from tripping the relay so just the 27/59 function can be checked.

Step 22. Connect a voltage source to the phase you wish to check.  The other two phases will need to be

connected to a voltage source with a voltage applied that is greater than the 27 setting in the
Normal Mode Settings.

Step 23. Close the breaker on the test set and wait for the RST LED to illuminate on the relay.

Step 24. Step the voltage down on one phase to a point lower than the 27 PU voltage and measure the

time from when the voltage is stepped down until the Trip 1 contacts close.  This timing should be
within ±5% or 30 milliseconds, whichever is greater, of the 27 TD setting that is set in the Relay
Settings screen.

Step 25. Return to the Tripping Logic screen and return the Trip 1 settings to the desired values.  Press

ESC to save the settings, then press ESC again to return to the Review/Edit Settings menu.

81 Timings

Step 26. From the Review/Edit Settings Menu, select 2, 5, 8, I, or L to enter the Tripping Logic screen for

the desired settings group.

Step 27. Enter a N in all Trip 1 locations except 81.  Enter a Y in the 81 location.  Press ESC to save these

settings, then press ESC again to return to the Review/Edit Settings menu.  This disables all other
functions from tripping the relay so just the 81 function can be checked.

Step 28. Connect the voltage inputs in parallel and connect a frequency source to the voltage inputs.  Set

the voltage level to a level greater than the 81 INH setting in the Normal Mode Settings.

Step 29. Close the breaker on the test set and wait for the RST LED to illuminate on the relay.

Step 30. Step the frequency down to a point below the 81 T HZ setting and measure the time from when

the frequency is stepped down until the Trip 1 contacts close.  This timing should be within ±10%
or 50 ms of the 81 T TD setting that is set in the Relay Settings screen.

Содержание BE1-DFPR








































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-DFPR

Pilz PNOZ X9 Operating Manual preview
PNOZ X9
Бренд: Pilz Страницы: 26
Motor Saver SymCom 77C Installation Instruction preview
SymCom 77C
Бренд: Motor Saver Страницы: 12
resideo Protectorelay Installation Instructions Manual preview
Protectorelay
Бренд: resideo Страницы: 8
hager EU302 User Instructions preview
EU302
Бренд: hager Страницы: 2
Ice NP800R Installation Manual preview
NP800R
Бренд: Ice Страницы: 18
ABB REJ 523 Technical Reference Manual preview
REJ 523
Бренд: ABB Страницы: 68
ABB 2CDC 113 016 M9701 Operating Instructions Manual preview
2CDC 113 016 M9701
Бренд: ABB Страницы: 10
ABB 41-331.21 Instruction Leaflet preview
41-331.21
Бренд: ABB Страницы: 12
ABB CM-TCN Manual preview
CM-TCN
Бренд: ABB Страницы: 42
ABB CM Instruction Leaflet preview
CM
Бренд: ABB Страницы: 12
ABB CIRCUIT SHIELD 237F Series Instructions Manual preview
CIRCUIT SHIELD 237F Series
Бренд: ABB Страницы: 15
ABB COV Series Instruction Leaflet preview
COV Series
Бренд: ABB Страницы: 24
ABB CVX Instruction Leaflet preview
CVX
Бренд: ABB Страницы: 20
ABB CT-AHS Safety Instruction preview
CT-AHS
Бренд: ABB Страницы: 25
ABB ITH-T Series Installation, Operation & Maintenance Instructions Manual preview
ITH-T Series
Бренд: ABB Страницы: 10
ABB KLF Series Instruction Leaflet preview
KLF Series
Бренд: ABB Страницы: 22
ABB CM-MSS.12 Operating And Installation Instructions preview
CM-MSS.12
Бренд: ABB Страницы: 8
ABB CP Series Instruction Leaflet preview
CP Series
Бренд: ABB Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды