Basler BE1-DFPR Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 135

background image

BE1-DFPR Controls and Indicators

2-7

Figure 2-5. Magnetics Module, Front Panel

Horizontal Mount With Connection Plugs

MAGNETICS MODULE (Figure 2-5)

Input transformers in the magnetics module isolate the relay from the system and
step down the currents and voltages to the levels the internal circuits require. A
switch located behind the magnetics front panel is provided to connect the voltage
transformers in a wye or delta configuration. (Refer to Figure 2-6 for a cutaway
view of the switch.)

If four wire, line to neutral voltages are used, the wye/delta switch must be in the
wye position. If three wire, line to line voltages are used, the switch must be in the
delta position. If two wire, phase B, line to neutral voltage is used, the switch must
be in the wye position.

If the switch position is changed, the corresponding 3/1 PH WYE/DELTA setting in
the INSTALLATION SETTINGS screen must also be changed. In the
INSTALLATION SETTINGS screen, use setting 1 when the wye position is

selected for single-phase operation.
Use setting 2 when the delta position
is selected, and setting 3 when the
wye position is selected for three-
phase operation. Refer to the
INSTALLATION SETTINGS screen
under REVIEW/EDIT SETTINGS
menu as described in publication 9

2315 00 991,

Terminal Displays and

Settings.

Front panel connection plugs are
optional items. When present,
connection plugs are accessed by
removing the magnetics module front
panel. To remove the magnetics
module front panel, place a flat blade
tool in the notch at the top of the
panel. Pry the panel outward until
the panel snaps out, and then lift the
panel up and away from the relay
case.

Current and voltage inputs and
control outputs can be tested by
removing the connection plugs and
replacing them with test plugs (Basler
part number 10095 or G.E. model
XLA12A). Doing this disconnects
these inputs and outputs from the
relay internal circuits. With the test
plugs installed, test inputs can be
injected, and the relay trip and close
outputs can be monitored.

«
...
53
54
55
56
57
...
»

Содержание BE1-DFPR








































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-DFPR

Бренд: ABB Страницы: 40

Бренд: Motor Saver Страницы: 12

Бренд: F&F Страницы: 4

Бренд: F&F Страницы: 2

Бренд: F&F Страницы: 4

Бренд: F&F Страницы: 8

Бренд: F&F Страницы: 7

Бренд: macromatic Страницы: 2

Бренд: Datakom Страницы: 19

Бренд: Eaton Страницы: 64

Бренд: CHINT Страницы: 12

Бренд: Zamel Страницы: 2

Бренд: MICROENER Страницы: 35

Бренд: GreenIQ Страницы: 2

Бренд: Woodward Страницы: 96

Бренд: CARLO GAVAZZI Страницы: 7

Бренд: hitin Страницы: 9

Бренд: Basler Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды